Re: [net-next PATCH v3 2/3] net: dsa: Add Airoha AN8855 5-Port Gigabit DSA Switch driver

[Christophe JAILLET]

Le 06/11/2024 à 13:22, Christian Marangi a écrit :
> Add Airoha AN8855 5-Port Gigabit DSA switch.
>
> The switch is also a nvmem-provider as it does have EFUSE to calibrate
> the internal PHYs.
>
> Signed-off-by: Christian Marangi <ansuelsmth-Re5JQEeQqe8AvxtiuMwx3w@xxxxxxxxxxxxxxxx>
> ---

Hi,

...

> +#include <linux/bitfield.h>
> +#include <linux/ethtool.h>
> +#include <linux/etherdevice.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/if_bridge.h>
> +#include <linux/iopoll.h>
> +#include <linux/mdio.h>
> +#include <linux/netdevice.h>
> +#include <linux/of_mdio.h>
> +#include <linux/of_net.h>
> +#include <linux/of_platform.h>
> +#include <linux/nvmem-provider.h>

Could be moved a few lines above to keep order.

> +#include <linux/phylink.h>
> +#include <linux/regmap.h>
> +#include <net/dsa.h>
...

> +static int an8855_port_fdb_dump(struct dsa_switch *ds, int port,
> +				dsa_fdb_dump_cb_t *cb, void *data)
> +{
> +	struct an8855_priv *priv = ds->priv;
> +	struct an8855_fdb _fdb = {  };

Should it but reseted in the do loop below, instead of only once here?

> +	int banks, count = 0;
> +	u32 rsp;
> +	int ret;
> +	int i;
> +
> +	mutex_lock(&priv->reg_mutex);
> +
> +	/* Load search port */
> +	ret = regmap_write(priv->regmap, AN8855_ATWD2,
> +			   FIELD_PREP(AN8855_ATWD2_PORT, port));
> +	if (ret)
> +		goto exit;
> +	ret = an8855_fdb_cmd(priv, AN8855_ATC_MAT(AND8855_FDB_MAT_MAC_PORT) |
> +			     AN8855_FDB_START, &rsp);
> +	if (ret < 0)
> +		goto exit;
> +
> +	do {
> +		/* From response get the number of banks to read, exit if 0 */
> +		banks = FIELD_GET(AN8855_ATC_HIT, rsp);
> +		if (!banks)
> +			break;
> +
> +		/* Each banks have 4 entry */
> +		for (i = 0; i < 4; i++) {
> +			count++;
> +
> +			/* Check if bank is present */
> +			if (!(banks & BIT(i)))
> +				continue;
> +
> +			/* Select bank entry index */
> +			ret = regmap_write(priv->regmap, AN8855_ATRDS,
> +					   FIELD_PREP(AN8855_ATRD_SEL, i));
> +			if (ret)
> +				break;
> +			/* wait 1ms for the bank entry to be filled */
> +			usleep_range(1000, 1500);
> +			an8855_fdb_read(priv, &_fdb);
> +
> +			if (!_fdb.live)
> +				continue;
> +			ret = cb(_fdb.mac, _fdb.vid, _fdb.noarp, data);
> +			if (ret < 0)
> +				break;
> +		}
> +
> +		/* Stop if reached max FDB number */
> +		if (count >= AN8855_NUM_FDB_RECORDS)
> +			break;
> +
> +		/* Read next bank */
> +		ret = an8855_fdb_cmd(priv, AN8855_ATC_MAT(AND8855_FDB_MAT_MAC_PORT) |
> +				     AN8855_FDB_NEXT, &rsp);
> +		if (ret < 0)
> +			break;
> +	} while (true);
> +
> +exit:
> +	mutex_unlock(&priv->reg_mutex);
> +	return ret;
> +}

...

> +	ret = regmap_set_bits(priv->regmap, AN8855_RG_RATE_ADAPT_CTRL_0,
> +			      AN8855_RG_RATE_ADAPT_RX_BYPASS |
> +			      AN8855_RG_RATE_ADAPT_TX_BYPASS |
> +			      AN8855_RG_RATE_ADAPT_RX_EN |
> +			      AN8855_RG_RATE_ADAPT_TX_EN);
> +	if (ret)
> +		return ret;
> +
> +	/* Disable AN if not in autoneg */
> +	ret = regmap_update_bits(priv->regmap, AN8855_SGMII_REG_AN0, BMCR_ANENABLE,
> +				 neg_mode == PHYLINK_PCS_NEG_INBAND_ENABLED ? BMCR_ANENABLE :
> +									      0);

Should 'ret' be tested here?

> +
> +	if (interface == PHY_INTERFACE_MODE_SGMII &&
> +	    neg_mode == PHYLINK_PCS_NEG_INBAND_DISABLED) {
> +		ret = regmap_set_bits(priv->regmap, AN8855_PHY_RX_FORCE_CTRL_0,
> +				      AN8855_RG_FORCE_TXC_SEL);
> +		if (ret)
> +			return ret;
> +	}

...

> +	priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL);
> +	if (!priv->ds)
> +		return -ENOMEM;
> +
> +	priv->ds->dev = &mdiodev->dev;
> +	priv->ds->num_ports = AN8855_NUM_PORTS;
> +	priv->ds->priv = priv;
> +	priv->ds->ops = &an8855_switch_ops;
> +	mutex_init(&priv->reg_mutex);

devm_mutex_init() to slightly simplify the remove function?

> +	priv->ds->phylink_mac_ops = &an8855_phylink_mac_ops;
> +
> +	priv->pcs.ops = &an8855_pcs_ops;
> +	priv->pcs.neg_mode = true;
> +	priv->pcs.poll = true;
> +
> +	ret = an8855_sw_register_nvmem(priv);
> +	if (ret)
> +		return ret;
> +
> +	dev_set_drvdata(&mdiodev->dev, priv);
> +
> +	return dsa_register_switch(priv->ds);
> +}
> +
> +static void
> +an8855_sw_remove(struct mdio_device *mdiodev)
> +{
> +	struct an8855_priv *priv = dev_get_drvdata(&mdiodev->dev);
> +
> +	dsa_unregister_switch(priv->ds);
> +	mutex_destroy(&priv->reg_mutex);
> +}
> +
> +static const struct of_device_id an8855_of_match[] = {
> +	{ .compatible = "airoha,an8855" },
> +	{ /* sentinel */ },

Ending comma is usually not needed after a terminator.

> +};
> +
> +static struct mdio_driver an8855_mdio_driver = {
> +	.probe = an8855_sw_probe,
> +	.remove = an8855_sw_remove,
> +	.mdiodrv.driver = {
> +		.name = "an8855",
> +		.of_match_table = an8855_of_match,
> +	},
> +};

...

> +#define	  AN8855_VA0_VTAG_EN		BIT(10) /* Per VLAN Egress Tag Control */
> +#define	  AN8855_VA0_IVL_MAC		BIT(5) /* Independent VLAN Learning */
> +#define	  AN8855_VA0_VLAN_VALID		BIT(0) /* VLAN Entry Valid */
> +#define AN8855_VAWD1			0x10200608
> +#define	  AN8855_VA1_PORT_STAG		BIT(1)
> +
> +/* Same register map of VAWD0 */

Not sure to follow. AN8855_VAWD0 above is 0x10200604, not 0x10200618

> +#define AN8855_VARD0			0x10200618
> +
> +enum an8855_vlan_egress_attr {
> +	AN8855_VLAN_EGRESS_UNTAG = 0,
> +	AN8855_VLAN_EGRESS_TAG = 2,
> +	AN8855_VLAN_EGRESS_STACK = 3,
> +};
> +
> +/* Register for port STP state control */
> +#define AN8855_SSP_P(x)			(0x10208000 + ((x) * 0x200))
> +#define	 AN8855_FID_PST			GENMASK(1, 0)
> +
> +enum an8855_stp_state {
> +	AN8855_STP_DISABLED = 0,
> +	AN8855_STP_BLOCKING = 1,
> +	AN8855_STP_LISTENING = 1,

Just wondering if this 0, 1, *1*, 2, 3 was intentional?

> +	AN8855_STP_LEARNING = 2,
> +	AN8855_STP_FORWARDING = 3
> +};
> +
> +/* Register for port control */
> +#define AN8855_PCR_P(x)			(0x10208004 + ((x) * 0x200))
> +#define	  AN8855_EG_TAG			GENMASK(29, 28)
> +#define	  AN8855_PORT_PRI		GENMASK(26, 24)
> +#define	  AN8855_PORT_TX_MIR		BIT(20)
> +#define	  AN8855_PORT_RX_MIR		BIT(16)
> +#define	  AN8855_PORT_VLAN		GENMASK(1, 0)
> +
> +enum an8855_port_mode {
> +	/* Port Matrix Mode: Frames are forwarded by the PCR_MATRIX members. */
> +	AN8855_PORT_MATRIX_MODE = 0,
> +
> +	/* Fallback Mode: Forward received frames with ingress ports that do
> +	 * not belong to the VLAN member. Frames whose VID is not listed on
> +	 * the VLAN table are forwarded by the PCR_MATRIX members.
> +	 */
> +	AN8855_PORT_FALLBACK_MODE = 1,
> +
> +	/* Check Mode: Forward received frames whose ingress do not
> +	 * belong to the VLAN member. Discard frames if VID ismiddes on the
> +	 * VLAN table.
> +	 */
> +	AN8855_PORT_CHECK_MODE = 1,

Just wondering if this 0, 1, *1*, 3 was intentional?

> +
> +	/* Security Mode: Discard any frame due to ingress membership
> +	 * violation or VID missed on the VLAN table.
> +	 */
> +	AN8855_PORT_SECURITY_MODE = 3,
> +};
...

CJ