Re: [PATCH 09/13] dt-bindings: phy: Add documentation for Airoha AN7581 USB PHY

[Christian Marangi]

On Mon, Mar 10, 2025 at 05:34:56PM +0100, Krzysztof Kozlowski wrote:
> On 09/03/2025 14:29, Christian Marangi wrote:
> > Add documentation for Airoha AN7581 USB PHY that describe the USB PHY
> > for the USB controller.
> > 
> > Airoha AN7581 SoC support a maximum of 2 USB port. The USB 2.0 mode is
> > always supported. The USB 3.0 mode is optional and depends on the Serdes
> > mode currently configured on the system for the USB port. If USB 3.0 node
> > is defined, then airoha,scu-ssr property is required for Serdes mode
> > validation.
> > 
> > Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx>
> > ---
> >  .../bindings/phy/airoha,an7581-usb-phy.yaml   | 106 ++++++++++++++++++
> >  MAINTAINERS                                   |   6 +
> >  2 files changed, 112 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml b/Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml
> > new file mode 100644
> > index 000000000000..39127cfb63a7
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml
> > @@ -0,0 +1,106 @@
> > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/phy/airoha,an7581-usb-phy.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Airoha AN7581 SoC USB PHY
> > +
> > +maintainers:
> > +  - Christian Marangi <ansuelsmth@xxxxxxxxx>
> > +
> > +description: >
> > +  The Airoha AN7581 SoC USB PHY describes the USB PHY for the USB controller.
> > +
> > +  Airoha AN7581 SoC support a maximum of 2 USB port. The USB 2.0 mode is
> > +  always supported. The USB 3.0 mode is optional and depends on the Serdes
> > +  mode currently configured on the system for the USB port. If USB 3.0 node
> > +  is defined, then airoha,scu-ssr property is required for Serdes mode
> > +  validation.
> > +
> > +properties:
> > +  compatible:
> > +    const: airoha,an7581-usb-phy
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  airoha,port-id:
> > +    description: Describe the physical port this USB PHY refer to. A dedicated
> > +      osciallator is used for each port for the USB 2.0 Slew Rate calibration.
> 
> typo
> 
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +    enum: [0, 1]
> 
> I don't understand why do you need index property here (which are
> usually not allowed).
>

Eh... As said in the description this is really to differentiate the 2
different physical port...

Each port have a dedicated oscillator for calibration and these
calibration are identified by an offset (all placed one after another in
a separate register space).

Oscillator 0 for physical port 0
Oscillator 1 for physcial port 1

And model this is a bit problematic without an additional property, any
hint for this?

> > +
> > +  airoha,scu-ssr:
> > +    description: Phandle to the SCU SSR node for USB 3.0 Serdes mode validation.
> > +    $ref: /schemas/types.yaml#/definitions/phandle
> > +
> > +  usb2-phy:
> > +    type: object
> > +
> > +    properties:
> > +      '#phy-cells':
> > +        const: 1
> > +
> > +    required:
> > +      - '#phy-cells'
> > +
> > +    additionalProperties: false
> 
> Also no resources in usb[23]-phy, so this goes to the parent level and
> you have phy-cells=2. Your DTS gives some hint that devices actually
> differ but the commit msg contradicts it, so I don't get. Do you have
> same IP block here or two different?
> 

SoC have 2 physical USB port.

Physical port 0 on address: 0x1fab0000
Physcial port 1 on address: 0x1fad0000

In those space there are registers to configure USB 2.0 mode and USB 3.0
mode for each physical port.

So yes no child node, phy-cells 2 and reference with phys = <&usb_phy 0
PHY_TYPE_USB2>, <&usb_phy 1 PHY_TYPE_USB3>; that totally works and hope
now the HW is more clear.

The real problematic part is the one above with identify the 2 physical
port.

> > +
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index fe34c80b8d52..c2dd385e9165 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -753,6 +753,12 @@ S:	Maintained
> >  F:	Documentation/devicetree/bindings/spi/airoha,en7581-snand.yaml
> >  F:	drivers/spi/spi-airoha-snfi.c
> >  
> > +AIROHA USB PHY DRIVER
> > +M:	Christian Marangi <ansuelsmth@xxxxxxxxx>
> > +L:	linux-arm-kernel@xxxxxxxxxxxxxxxxxxx (moderated for non-subscribers)
> > +S:	Maintained
> > +F:	Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yam
> 
> Typo in extension/missing l.
> 
> 
> 
> Best regards,
> Krzysztof

-- 
	Ansuel