Re: [PATCH 2/3] clk: add TI CDCE6214 clock driver

From: Sascha Hauer
Date: Tue Apr 08 2025 - 09:50:17 EST

Next message: Zijun Hu: "[PATCH net-next] sock: Correct error checking condition for assign|release_proto_idx()"
Previous message: Alexander Stein: "[PATCH 1/1] arm64: defconfig: enable backlight device class"
In reply to: Sascha Hauer: "[PATCH 2/3] clk: add TI CDCE6214 clock driver"
Next in thread: Sascha Hauer: "[PATCH 3/3] dt-bindings: clock: add TI CDCE6214 binding"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Tue, Apr 08, 2025 at 02:00:23PM +0200, Sascha Hauer wrote:
> The CDCE6214 is a Ultra-Low Power Clock Generator With One PLL, Four
> Differential Outputs, Two Inputs, and Internal EEPROM. This patch adds
> a common clk framework driver for this chip.
>
> - Two inputs (PRIREF and SECREF)
> - Programmable 8bit divider or x2 multiplier between input and PLL
> - 16b integer / 24bit fractional PLL
> - Two programmable /4, /5, /6 dividers after PLL (PSA/PSB)
> - Four outputs (OUT1-OUT4) with programmable 14b dividers,
> muxable between PSA, PSB and PLL input
> - One output (OUT0) fed from PLL input
>
> - PRIREF can be configured as LVCMOS or differential input
> - SECREF can be configured as LVCMOS, differential or oscillator input
> - OUT0 is a LVCMOS output
> - OUT1 and OUT4 can be configured as LVDS, LP-HCSL or LVCMOS outputs
> - OUT2 and OUT3 can be configured as LVDS or LP-HCSL outputs
>
> All clocks are registered without parent rate propagation, so each of
> the clocks must be configured separately via device tree or consumer.
>
> Signed-off-by: Alvin Šipraga <alsi@xxxxxxxxxxxxxxx>
> Signed-off-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
> ---
> drivers/clk/Kconfig | 7 +
> drivers/clk/Makefile | 1 +
> drivers/clk/clk-cdce6214.c | 1105 +++++++++++++++++++++++++++++++
> include/dt-bindings/clock/ti,cdce6214.h | 24 +
> 4 files changed, 1137 insertions(+)
>
> diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
> index 713573b6c86c7..499fd610c0467 100644
> --- a/drivers/clk/Kconfig
> +++ b/drivers/clk/Kconfig
> @@ -170,6 +170,13 @@ config COMMON_CLK_BM1880
> help
> This driver supports the clocks on Bitmain BM1880 SoC.
>
> +config COMMON_CLK_CDCE6214
> + tristate "Clock driver for TI CDCE6214 clock synthesizer"
> + depends on I2C
> + select REGMAP_I2C
> + help
> + This driver supports TI CDCE6214 programmable 1-PLL clock synthesizer.
> +
> config COMMON_CLK_CDCE706
> tristate "Clock driver for TI CDCE706 clock synthesizer"
> depends on I2C
> diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
> index bf4bd45adc3a0..0f87b13b137b5 100644
> --- a/drivers/clk/Makefile
> +++ b/drivers/clk/Makefile
> @@ -49,6 +49,7 @@ obj-$(CONFIG_COMMON_CLK_AXI_CLKGEN) += clk-axi-clkgen.o
> obj-$(CONFIG_ARCH_AXXIA) += clk-axm5516.o
> obj-$(CONFIG_COMMON_CLK_BD718XX) += clk-bd718x7.o
> obj-$(CONFIG_COMMON_CLK_BM1880) += clk-bm1880.o
> +obj-$(CONFIG_COMMON_CLK_CDCE6214) += clk-cdce6214.o
> obj-$(CONFIG_COMMON_CLK_CDCE706) += clk-cdce706.o
> obj-$(CONFIG_COMMON_CLK_CDCE925) += clk-cdce925.o
> obj-$(CONFIG_ARCH_CLPS711X) += clk-clps711x.o
> diff --git a/drivers/clk/clk-cdce6214.c b/drivers/clk/clk-cdce6214.c
> new file mode 100644
> index 0000000000000..a825cd71bb11b
> --- /dev/null
> +++ b/drivers/clk/clk-cdce6214.c
> @@ -0,0 +1,1105 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Driver for the TI CDCE6214 clock generator
> + *
> + * Copyright (c) 2023 Alvin Šipraga <alsi@xxxxxxxxxxxxxxx>
> + * Copyright (c) 2025 Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
> + */
> +
> +#include <linux/i2c.h>
> +#include <linux/of.h>
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <dt-bindings/clock/ti,cdce6214.h>
> +
> +#define RO_I2C_A0 BIT(15)
> +#define RO_PDN_INPUT_SEL BIT(14)
> +#define RO_GPIO4_DIR_SEL BIT(13)
> +#define RO_GPIO1_DIR_SEL BIT(12)
> +#define RO_ZDM_CLOCKSEL BIT(10)
> +#define RO_ZDM_EN BIT(8)
> +#define RO_SYNC BIT(5)
> +#define RO_RECAL BIT(4)
> +#define RO_RESETN_SOFT BIT(3)
> +#define RO_SWRST BIT(2)
> +#define RO_POWERDOWN BIT(1)
> +#define RO_MODE BIT(0)
> +
> +#define R1_GPIO4_INPUT_SEL GENMASK(15, 12)
> +#define R1_GPIO3_INPUT_SEL GENMASK(11, 8)
> +#define R1_GPIO2_INPUT_SEL GENMASK(7, 4)
> +#define R1_GPIO1_INPUT_SEL GENMASK(3, 0)
> +
> +#define R2_GPIO4_OUTPUT_SEL GENMASK(9, 6)
> +#define R2_GPIO1_OUTPUT_SEL GENMASK(5, 2)
> +#define R2_REFSEL_SW GENMASK(1, 0)
> +
> +#define R3_DISABLE_CRC BIT(13)
> +#define R3_UPDATE_CRC BIT(12)
> +#define R3_NVMCOMMIT BIT(11)
> +#define R3_REGCOMMIT BIT(10)
> +#define R3_REGCOMMIT_PAGE BIT(9)
> +#define R3_FREQ_DEC_REG BIT(6)
> +#define R3_FREQ_INC_REG BIT(5)
> +#define R3_FREQ_INC_DEC_REG_MODE BIT(4)
> +#define R3_FREQ_INC_DEC_EN BIT(3)
> +
> +#define R4_CH4_PD BIT(7)
> +#define R4_CH3_PD BIT(6)
> +#define R4_CH2_PD BIT(5)
> +#define R4_CH1_PD BIT(4)
> +#define R4_POST_EE_DLY GENMASK(3, 0)
> +
> +#define R5_PLL_VCOBUFF_LDO_PD BIT(8)
> +#define R5_PLL_VCO_LDO_PD BIT(7)
> +#define R5_PLL_VCO_BUFF_PD BIT(6)
> +#define R5_PLL_CP_LDO_PD BIT(5)
> +#define R5_PLL_LOCKDET_PD BIT(4)
> +#define R5_PLL_PSB_PD BIT(3)
> +#define R5_PLL_PSA_PD BIT(2)
> +#define R5_PLL_PFD_PD BIT(1)
> +
> +#define R7_NVMCRCERR BIT(5)
> +#define R7_LOCK_DET_S BIT(1)
> +#define R7_LOCK_DET BIT(0)
> +
> +#define R9_NVMLCRC GENMASK(15, 0)
> +
> +#define R10_NVMSCRC GENMASK(15, 0)
> +
> +#define R11_NVM_RD_ADDR GENMASK(5, 0)
> +
> +#define R12_NVM_RD_DATA GENMASK(15, 0)
> +
> +#define R13_NVM_WR_ADDR GENMASK(5, 0)
> +
> +#define R14_NVM_WR_DATA GENMASK(15, 0)
> +
> +#define R15_EE_LOCK GENMASK(15, 12)
> +#define R15_CAL_MUTE BIT(5)
> +
> +#define R24_IP_PRIREF_BUF_SEL BIT(15)
> +#define R24_IP_XO_CLOAD GENMASK(12, 8)
> +#define R24_IP_BIAS_SEL_XO GENMASK(5, 2)
> +#define R24_IP_SECREF_BUF_SEL GENMASK(1, 0)
> +#define R24_IP_SECREF_BUF_SEL_XTAL 0
> +#define R24_IP_SECREF_BUF_SEL_LVCMOS 1
> +#define R24_IP_SECREF_BUF_SEL_DIFF 2
> +
> +#define R25_IP_REF_TO_OUT4_EN BIT(14)
> +#define R25_IP_REF_TO_OUT3_EN BIT(13)
> +#define R25_IP_REF_TO_OUT2_EN BIT(12)
> +#define R25_IP_REF_TO_OUT1_EN BIT(11)
> +#define R25_IP_BYP_OUT0_EN BIT(10)
> +#define R25_REF_CH_MUX BIT(9)
> +#define R25_IP_RDIV GENMASK(7, 0)
> +
> +#define R27_MASH_ORDER GENMASK(1, 0)
> +
> +#define R30_PLL_NDIV GENMASK(14, 0)
> +
> +#define R31_PLL_NUM_15_0 GENMASK(15, 0)
> +
> +#define R32_PLL_NUM_23_16 GENMASK(7, 0)
> +
> +#define R33_PLL_DEN_15_0 GENMASK(15, 0)
> +
> +#define R34_PLL_DEN_23_16 GENMASK(7, 0)
> +
> +#define R41_SSC_EN BIT(15)
> +
> +#define R42_SSC_TYPE BIT(5)
> +#define R42_SSC_SEL GENMASK(3, 1)
> +
> +#define R43_FREQ_INC_DEC_DELTA GENMASK(15, 0)
> +
> +#define R47_PLL_CP_DN GENMASK(12, 7)
> +#define R47_PLL_PSB GENMASK(6, 5)
> +#define R47_PLL_PSA GENMASK(4, 3)
> +
> +#define R48_PLL_LF_RES GENMASK(14, 11)
> +#define R48_PLL_CP_UP GENMASK(5, 0)
> +
> +#define R49_PLL_LF_ZCAP GENMASK(4, 0)
> +
> +#define R50_PLL_LOCKDET_WINDOW GENMASK(10, 8)
> +
> +#define R51_PLL_PFD_DLY_EN BIT(10)
> +#define R51_PLL_PFD_CTRL BIT(6)
> +
> +#define R52_PLL_NCTRL_EN BIT(6)
> +#define R52_PLL_CP_EN BIT(3)
> +
> +#define R55_PLL_LF_3_PCTRIM GENMASK(9, 8)
> +#define R55_PLL_LF_3_PRTRIM GENMASK(7, 6)
> +
> +#define R56_CH1_MUX GENMASK(15, 14)
> +#define R56_CH1_DIV GENMASK(13, 0)
> +
> +#define R57_CH1_LPHCSL_EN BIT(14)
> +#define R57_CH1_1P8VDET BIT(12)
> +#define R57_CH1_GLITCHLESS_EN BIT(9)
> +#define R57_CH1_SYNC_DELAY GENMASK(8, 4)
> +#define R57_CH1_SYNC_EN BIT(3)
> +#define R57_CH1_MUTE_SEL BIT(1)
> +#define R57_CH1_MUTE BIT(0)
> +
> +#define R59_CH1_LVDS_EN BIT(15)
> +#define R59_CH1_CMOSN_EN BIT(14)
> +#define R59_CH1_CMOSP_EN BIT(13)
> +#define R59_CH1_CMOSN_POL BIT(12)
> +#define R59_CH1_CMOSP_POL BIT(11)
> +
> +#define R60_CH1_DIFFBUF_IBIAS_TRIM GENMASK(15, 12)
> +#define R60_CH1_LVDS_CMTRIM_INC GENMASK(11, 10)
> +#define R60_CH1_LVDS_CMTRIM_DEC GENMASK(5, 4)
> +#define R60_CH1_CMOS_SLEW_RATE_CTRL GENMASK(3, 0)
> +
> +#define R62_CH2_MUX GENMASK(15, 14)
> +#define R62_CH2_DIV GENMASK(13, 0)
> +
> +#define R63_CH2_LPHCSL_EN BIT(13)
> +#define R63_CH2_1P8VDET BIT(12)
> +#define R63_CH2_GLITCHLESS_EN BIT(9)
> +#define R63_CH2_SYNC_DELAY GENMASK(8, 4)
> +#define R63_CH2_SYNC_EN BIT(3)
> +#define R63_CH2_MUTE_SEL BIT(1)
> +#define R63_CH2_MUTE BIT(0)
> +
> +#define R65_CH2_LVDS_CMTRIM_DEC GENMASK(14, 13)
> +#define R65_CH2_LVDS_EN BIT(11)
> +
> +#define R66_CH2_LVDS_CMTRIM_IN GENMASK(5, 4)
> +#define R66_CH2_DIFFBUF_IBIAS_TRIM GENMASK(3, 0)
> +
> +#define R67_CH3_MUX GENMASK(15, 14)
> +#define R67_CH3_DIV GENMASK(13, 0)
> +
> +#define R68_CH3_LPHCSL_EN BIT(13)
> +#define R68_CH3_1P8VDET BIT(12)
> +#define R68_CH3_GLITCHLESS_EN BIT(9)
> +#define R68_CH3_SYNC_DELAY GENMASK(8, 4)
> +#define R68_CH3_SYNC_EN BIT(3)
> +#define R68_CH3_MUTE_SEL BIT(1)
> +#define R68_CH3_MUTE BIT(0)
> +
> +#define R70_CH3_LVDS_EN BIT(11)
> +
> +#define R71_CH3_LVDS_CMTRIM_DEC GENMASK(10, 9)
> +#define R71_CH3_LVDS_CMTRIM_INC GENMASK(5, 4)
> +#define R71_CH3_DIFFBUF_IBIAS_TR GENMASK(3, 0)
> +
> +#define R72_CH4_MUX GENMASK(15, 14)
> +#define R72_CH4_DIV GENMASK(13, 0)
> +
> +#define R73_CH4_LPHCSL_EN BIT(13)
> +#define R73_CH4_1P8VDET BIT(12)
> +#define R73_CH4_GLITCHLESS_EN BIT(9)
> +#define R73_CH4_SYNC_DELAY GENMASK(8, 4)
> +#define R73_CH4_SYNC_EN BIT(3)
> +#define R73_CH4_MUTE_SEL BIT(1)
> +#define R73_CH4_MUTE BIT(0)
> +
> +#define R75_CH4_LVDS_EN BIT(15)
> +#define R75_CH4_CMOSP_EN BIT(14)
> +#define R75_CH4_CMOSN_EN BIT(13)
> +#define R75_CH4_CMOSP_POL BIT(12)
> +#define R75_CH4_CMOSN_POL BIT(11)
> +
> +#define R76_CH4_DIFFBUF_IBIAS_TRIM GENMASK(9, 6)
> +#define R76_CH4_LVDS_CMTRIM_IN GENMASK(5, 4)
> +#define R76_CH4_CMOS_SLEW_RATE_CTRL GENMASK(3, 0)
> +
> +#define R77_CH4_LVDS_CMTRIM_DEC GENMASK(1, 0)
> +
> +#define R78_CH0_EN BIT(12)
> +
> +#define R79_SAFETY_1P8V_MODE BIT(9)
> +#define R79_CH0_CMOS_SLEW_RATE_CTRL GENMASK(3, 0)
> +
> +#define R81_PLL_LOCK_MASK BIT(3)
> +
> +#define CDCE6214_VCO_MIN 2335000000
> +#define CDCE6214_VCO_MAX 2625000000
> +#define CDCE6214_DENOM_DEFAULT (1 << 24)
> +
> +static char *clk_names[] = {
> + [CDCE6214_CLK_PRIREF] = "priref",
> + [CDCE6214_CLK_SECREF] = "secref",
> + [CDCE6214_CLK_OUT0] = "out0",
> + [CDCE6214_CLK_OUT1] = "out1",
> + [CDCE6214_CLK_OUT2] = "out2",
> + [CDCE6214_CLK_OUT3] = "out3",
> + [CDCE6214_CLK_OUT4] = "out4",
> + [CDCE6214_CLK_PLL] = "pll",
> + [CDCE6214_CLK_PSA] = "psa",
> + [CDCE6214_CLK_PSB] = "psb",
> +};
> +
> +#define CDCE6214_NUM_CLOCKS ARRAY_SIZE(clk_names)
> +
> +struct cdce6214;
> +
> +struct cdce6214_clock {
> + struct clk_hw hw;
> + struct cdce6214 *priv;
> + int index;
> +};
> +
> +struct cdce6214_config {
> + const struct reg_default *reg_default;
> + int reg_default_size;
> +};

This is unused. I'll remove it next round.

> +static const struct of_device_id cdce6214_ids[] = {
> + {
> + .compatible = "ti,cdce6214-24mhz",

Should be ti,cdce6214. Will fix next round.

Sascha

--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |

Next message: Zijun Hu: "[PATCH net-next] sock: Correct error checking condition for assign|release_proto_idx()"
Previous message: Alexander Stein: "[PATCH 1/1] arm64: defconfig: enable backlight device class"
In reply to: Sascha Hauer: "[PATCH 2/3] clk: add TI CDCE6214 clock driver"
Next in thread: Sascha Hauer: "[PATCH 3/3] dt-bindings: clock: add TI CDCE6214 binding"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]