Re: [PATCH 2/4] arm64: dts: qcom: agatti: add LPASS devices

[Konrad Dybcio]

On 2/9/26 3:24 PM, Srinivas Kandagatla wrote:
> From: Alexey Klimov <alexey.klimov@xxxxxxxxxx>
> 
> The rxmacro, txmacro, vamacro, soundwire nodes, lpass clock
> controllers are required to support audio playback and
> audio capture on sm6115 and its derivatives.
> 
> Signed-off-by: Alexey Klimov <alexey.klimov@xxxxxxxxxx>
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxxxxxxxx>
> ---

[...]

> +		rxmacro: codec@a600000 {
> +			compatible = "qcom,sm6115-lpass-rx-macro";
> +			reg = <0x0 0xa600000 0x0 0x1000>;
> +
> +			clocks = <&q6afecc LPASS_CLK_ID_RX_CORE_MCLK
> +				LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6afecc LPASS_CLK_ID_RX_CORE_NPL_MCLK
> +				 LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6afecc LPASS_HW_DCODEC_VOTE
> +				 LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&vamacro>;
> +			clock-names = "mclk",
> +				      "npl",
> +				      "dcodec",
> +				      "fsgen";
> +			assigned-clocks = <&q6afecc LPASS_CLK_ID_RX_CORE_MCLK
> +					  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +					  <&q6afecc LPASS_CLK_ID_RX_CORE_NPL_MCLK
> +					  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +			assigned-clock-rates = <22579200>,
> +					       <22579200>;

Is this necessary?

> +			#clock-cells = <0>;
> +			clock-output-names = "mclk";
> +			#sound-dai-cells = <1>;
> +		};
> +
> +		swr1: soundwire@a610000 {
> +			compatible = "qcom,soundwire-v1.6.0";
> +			reg = <0x0 0x0a610000 0x0 0x2000>;

Let's set size=0x10_000 (it's got that much reserved for it)

> +			interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			clocks = <&rxmacro>;
> +			clock-names = "iface";
> +
> +			resets = <&lpass_audiocc 0>;
> +			reset-names = "swr_audio_cgcr";
> +
> +			label = "RX";
> +			qcom,din-ports = <0>;
> +			qcom,dout-ports = <5>;
> +
> +			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x1f 0x1f 0x07 0x00>;
> +			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0b 0x01 0x00>;
> +			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
> +			qcom,ports-hstart =		/bits/ 8 <0xff 0x03 0xff 0xff 0xff>;
> +			qcom,ports-hstop =		/bits/ 8 <0xff 0x06 0xff 0xff 0xff>;
> +			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
> +			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0x00 0x01 0xff 0xff>;
> +			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0x00>;
> +			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
> +
> +			status = "disabled";

No need to disable, I think

> +
> +			#sound-dai-cells = <1>;
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +		};
> +
> +
> +		txmacro: codec@a620000 {
> +			compatible = "qcom,sm6115-lpass-tx-macro";
> +			reg = <0x0 0x0a620000 0x0 0x1000>;
> +
> +			clocks = <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK
> +				 LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK
> +				 LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6afecc LPASS_HW_DCODEC_VOTE
> +				 LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&vamacro>;
> +			clock-names = "mclk",
> +				      "npl",
> +				      "dcodec",
> +				      "fsgen";
> +			assigned-clocks = <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK
> +					  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +					  <&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK
> +					  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +			assigned-clock-rates = <19200000>,
> +					       <19200000>;

Is this necessary?

> +			#clock-cells = <0>;
> +			clock-output-names = "mclk";
> +			#sound-dai-cells = <1>;
> +		};
> +
> +		lpass_audiocc: clock-controller@a6a9000 {
> +			compatible = "qcom,sm6115-lpassaudiocc";
> +			reg = <0x0 0x0a6a9000 0x0 0x1000>;

This region is called 'LPASS_AUDIO_CSR' with the correct size and length


> +			#reset-cells = <1>;
> +		};
> +
> +		vamacro: codec@a730000 {
> +			compatible = "qcom,sm6115-lpass-va-macro";
> +			reg = <0x0 0x0a730000 0x0 0x1000>;
> +
> +			clocks = <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK
> +				 LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6afecc LPASS_HW_DCODEC_VOTE
> +				 LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +				 <&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK
> +				 LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +			clock-names = "mclk",
> +				      "dcodec",
> +				      "npl";
> +			assigned-clocks = <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK
> +					  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> +					  <&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK
> +					  LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +			assigned-clock-rates = <19200000>,
> +					       <19200000>;


Is this necessary?


> +			#clock-cells = <0>;
> +			clock-output-names = "fsgen";
> +			#sound-dai-cells = <1>;
> +		};
> +
> +		swr0: soundwire@a740000 {
> +			compatible = "qcom,soundwire-v1.6.0";
> +			reg = <0x0 0x0a740000 0x0 0x2000>;

sz=0x10_000

> +			interrupts = <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&txmacro>;
> +			clock-names = "iface";
> +
> +			resets = <&lpasscc 0>;
> +			reset-names = "swr_audio_cgcr";
> +
> +			label = "VA_TX";
> +			qcom,din-ports = <3>;
> +			qcom,dout-ports = <0>;
> +
> +			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x03 0x03>;
> +			qcom,ports-offset1 =		/bits/ 8 <0x01 0x02 0x01>;
> +			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x00>;
> +			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff>;
> +			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff>;
> +			qcom,ports-word-length =	/bits/ 8 <0xff 0xff 0xff>;
> +			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0xff 0xff>;
> +			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff>;
> +			qcom,ports-lane-control =	/bits/ 8 <0x00 0x00 0x00>;
> +
> +			status = "disabled";

No need

> +
> +			#sound-dai-cells = <1>;
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +		};
> +
> +		lpasscc: clock-controller@a7ec000 {
> +			compatible = "qcom,sm6115-lpasscc";
> +			reg = <0x0 0x0a7ec000 0x0 0x1000>;

This isn't quite right.. it's at LPASS_TCSR (0xa7e0000) + 0xc000

Not sure if we're gonna need the rest of it in the future, but it may
be smart to describe the whole thing.. Too bad I didn't know about it
when I first submitted that driver...

Konrad