Re: [PATCH v3 1/4] dt-bindings: clock: qcom: Add QREF regulator supplies for glymur

[Krzysztof Kozlowski]

On 14/05/2026 12:22, Krzysztof Kozlowski wrote:
> On Wed, May 06, 2026 at 01:43:51AM -0700, Qiang Yu wrote:
>> Add regulator supply properties for the Glymur TCSR QREF/REFGEN blocks
>> required by clkref clocks.
>>
>> The vdda-qreftx*, vdda-qrefrpt*, and vdda-qrefrx* supplies map to common
>> QREF TX/RPT/RX components, while SoC-specific topology and instance count
>> differ. Document them here for qcom,glymur-tcsr.
>>
>> Signed-off-by: Qiang Yu <qiang.yu@xxxxxxxxxxxxxxxx>
>> ---
>>  .../bindings/clock/qcom,sm8550-tcsr.yaml           | 57 ++++++++++++++++++++++
>>  1 file changed, 57 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/clock/qcom,sm8550-tcsr.yaml b/Documentation/devicetree/bindings/clock/qcom,sm8550-tcsr.yaml
>> index 1ccdf4b0f5dd..57921cb63230 100644
>> --- a/Documentation/devicetree/bindings/clock/qcom,sm8550-tcsr.yaml
>> +++ b/Documentation/devicetree/bindings/clock/qcom,sm8550-tcsr.yaml
>> @@ -51,6 +51,63 @@ properties:
>>    '#reset-cells':
>>      const: 1
>>  
>> +  vdda-refgen-0p9-supply: true
>> +  vdda-refgen-1p2-supply: true
>> +  vdda-qrefrx0-0p9-supply: true
>> +  vdda-qrefrx1-0p9-supply: true
>> +  vdda-qrefrx2-0p9-supply: true
>> +  vdda-qrefrx4-0p9-supply: true
>> +  vdda-qrefrx5-0p9-supply: true
>> +  vdda-qreftx0-0p9-supply: true
>> +  vdda-qreftx0-1p2-supply: true
>> +  vdda-qreftx1-0p9-supply: true
>> +  vdda-qrefrpt0-0p9-supply: true
>> +  vdda-qrefrpt1-0p9-supply: true
>> +  vdda-qrefrpt2-0p9-supply: true
>> +  vdda-qrefrpt3-0p9-supply: true
>> +  vdda-qrefrpt4-0p9-supply: true
> 
> Either I do not understand your previous explanation:
> CXO -> TX0 -> RPT0 -> RPT1 -> RPT2 -> RX2 -> PCIe4_PHY
> 
> or this is still wrong. There is no TCSR here, so this proves nothing.
> If TCSR is TX0, then you do not have five of them...
> 
> My previous comment stay - you are not describing the actual hardware
> here.

And it should not be my task BUT YOURS to verify this in hardware
programming guide or manual, but nevertheless I did verify and the
manual DOES NOT mention these supplies. For Glymur, it mentions 8 reset
ports and 5 clock ports.

No supplies at all.

Then I went to QREF and it does mention few supplies but completely
different, like mx, cx, px 0.88 and px1.2, so none of this matches QREF
either.

Best regards,
Krzysztof