[PATCH v4 10/10] arm64: dts: qcom: hamoa: Enable CDSP cooling

[Gaurav Kohli]

From: Dipa Ramesh Mantre <dipa.mantre@xxxxxxxxxxxxxxxx>

Unlike the CPU, the CDSP does not throttle its speed automatically
when it reaches high temperatures in hamoa.

Set up CDSP cooling for both instances by throttling the cdsp, when
it reaches 95°C.

Signed-off-by: Dipa Ramesh Mantre <dipa.mantre@xxxxxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/hamoa.dtsi | 63 +++++++++++++++++++++++++++++++++++++
 1 file changed, 63 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/hamoa.dtsi b/arch/arm64/boot/dts/qcom/hamoa.dtsi
index 4ba751a65142..397049d2d238 100644
--- a/arch/arm64/boot/dts/qcom/hamoa.dtsi
+++ b/arch/arm64/boot/dts/qcom/hamoa.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/clock/qcom,x1e80100-gpucc.h>
 #include <dt-bindings/clock/qcom,x1e80100-tcsr.h>
 #include <dt-bindings/dma/qcom-gpi.h>
+#include <dt-bindings/firmware/qcom,qmi-tmd.h>
 #include <dt-bindings/interconnect/qcom,icc.h>
 #include <dt-bindings/interconnect/qcom,x1e80100-rpmh.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -8815,6 +8816,8 @@ remoteproc_cdsp: remoteproc@32300000 {
 
 			status = "disabled";
 
+			#cooling-cells = <3>;
+
 			glink-edge {
 				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
 							     IPCC_MPROC_SIGNAL_GLINK_QMP
@@ -9402,6 +9405,7 @@ aoss0-critical {
 		};
 
 		thermal_nsp0: nsp0-thermal {
+			polling-delay-passive = <200>;
 			thermal-sensors = <&tsens3 1>;
 
 			trips {
@@ -9411,15 +9415,30 @@ trip-point0 {
 					type = "hot";
 				};
 
+				nsp0_alert0: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
 				nsp0-critical {
 					temperature = <115000>;
 					hysteresis = <1000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&nsp0_alert0>;
+					cooling-device = <&remoteproc_cdsp QCOM_CDSP_TMD_CDSP_SW
+							 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		thermal_nsp1: nsp1-thermal {
+			polling-delay-passive = <200>;
 			thermal-sensors = <&tsens3 2>;
 
 			trips {
@@ -9429,15 +9448,30 @@ trip-point0 {
 					type = "hot";
 				};
 
+				nsp1_alert0: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
 				nsp1-critical {
 					temperature = <115000>;
 					hysteresis = <1000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&nsp1_alert0>;
+					cooling-device = <&remoteproc_cdsp QCOM_CDSP_TMD_CDSP_SW
+							 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		thermal_nsp2: nsp2-thermal {
+			polling-delay-passive = <200>;
 			thermal-sensors = <&tsens3 3>;
 
 			trips {
@@ -9447,15 +9481,30 @@ trip-point0 {
 					type = "hot";
 				};
 
+				nsp2_alert0: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
 				nsp2-critical {
 					temperature = <115000>;
 					hysteresis = <1000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&nsp2_alert0>;
+					cooling-device = <&remoteproc_cdsp QCOM_CDSP_TMD_CDSP_SW
+							 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		thermal_nsp3: nsp3-thermal {
+			polling-delay-passive = <200>;
 			thermal-sensors = <&tsens3 4>;
 
 			trips {
@@ -9465,12 +9514,26 @@ trip-point0 {
 					type = "hot";
 				};
 
+				nsp3_alert0: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
 				nsp3-critical {
 					temperature = <115000>;
 					hysteresis = <1000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&nsp3_alert0>;
+					cooling-device = <&remoteproc_cdsp QCOM_CDSP_TMD_CDSP_SW
+							 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		thermal_gpuss_0: gpuss-0-thermal {

-- 
2.34.1