Re: [PATCH 3/3] arm64: dts: qcom: rb3gen2: add Industrial BT UART overlay

[Dmitry Baryshkov]

On Thu, Jul 23, 2026 at 06:01:09PM +0530, Rahul Samana wrote:
> Add an overlay for the RB3 Gen 2 Industrial mezzanine variant that routes
> QCC2072 Bluetooth over UART4 and models the M.2 E-key connector graph
> endpoints for PCIe and UART.
> 
> The default Industrial mezzanine overlay describes the common mezzanine
> hardware. Build this variant by applying the common Industrial mezzanine
> overlay first, followed by the BT UART overlay, because the reworked board
> keeps the common mezzanine description and only changes the Bluetooth
> transport routing.
> 
> The overlay also disables the on-board WCN6750 PMU and UART7 path so the
> M.2 QCC2072 Bluetooth controller can be used instead.
> 
> Signed-off-by: Rahul Samana <rahul.samana@xxxxxxxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/Makefile                  |   2 +
>  ...s6490-rb3gen2-industrial-mezzanine-bt-uart.dtso | 133 +++++++++++++++++++++
>  2 files changed, 135 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 6f33c4e2f09c..45786d3db14a 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -179,8 +179,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= qcs6490-rb3gen2.dtb
>  
>  qcs6490-rb3gen2-vision-mezzanine-dtbs := qcs6490-rb3gen2.dtb qcs6490-rb3gen2-vision-mezzanine.dtbo
>  qcs6490-rb3gen2-industrial-mezzanine-dtbs := qcs6490-rb3gen2.dtb qcs6490-rb3gen2-industrial-mezzanine.dtbo
> +qcs6490-rb3gen2-industrial-mezzanine-bt-uart-dtbs := qcs6490-rb3gen2.dtb qcs6490-rb3gen2-industrial-mezzanine.dtbo qcs6490-rb3gen2-industrial-mezzanine-bt-uart.dtbo
>  
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs6490-rb3gen2-industrial-mezzanine.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= qcs6490-rb3gen2-industrial-mezzanine-bt-uart.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs6490-rb3gen2-vision-mezzanine.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs6490-thundercomm-minipc-g1iot.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs6490-thundercomm-rubikpi3.dtb
> diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2-industrial-mezzanine-bt-uart.dtso b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2-industrial-mezzanine-bt-uart.dtso
> new file mode 100644
> index 000000000000..06560df0a719
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2-industrial-mezzanine-bt-uart.dtso
> @@ -0,0 +1,133 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2026 Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +&{/} {
> +	vreg_wcn_3p3: regulator-wcn-3p3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VREG_WCN_3P3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		regulator-boot-on;
> +	};
> +
> +	m2_e_connector: m2-e-connector {

Kill unused labels. Everywhere.

> +		compatible = "pcie-m2-e-connector";
> +		vpcie3v3-supply = <&vreg_wcn_3p3>;
> +
> +		m2_e_ports: ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				m2_e_pcie_ep: endpoint@0 {
> +					reg = <0>;
> +					remote-endpoint = <&pcie0_m2_e_ep>;
> +				};
> +			};
> +
> +			port@3 {
> +				reg = <3>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				m2_e_uart_ep: endpoint@0 {
> +					reg = <0>;
> +					remote-endpoint = <&uart4_m2_e_ep>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&qup_uart4_cts {
> +	bias-bus-hold;
> +};
> +
> +&qup_uart4_rts {
> +	drive-strength = <2>;
> +	bias-disable;
> +};
> +
> +&qup_uart4_rx {
> +	bias-pull-up;
> +};
> +
> +&qup_uart4_tx {
> +	drive-strength = <2>;
> +	bias-disable;
> +};
> +
> +&tlmm {
> +	qup_uart4_sleep_cts: qup-uart4-sleep-cts-state {
> +		pins = "gpio16";
> +		function = "gpio";
> +		bias-bus-hold;
> +	};
> +
> +	qup_uart4_sleep_rts: qup-uart4-sleep-rts-state {
> +		pins = "gpio17";
> +		function = "gpio";
> +		bias-pull-down;
> +	};
> +
> +	qup_uart4_sleep_tx: qup-uart4-sleep-tx-state {
> +		pins = "gpio18";
> +		function = "gpio";
> +		bias-pull-up;
> +	};
> +
> +	qup_uart4_sleep_rx: qup-uart4-sleep-rx-state {
> +		pins = "gpio19";
> +		function = "gpio";
> +		bias-pull-up;
> +	};
> +};
> +
> +&pcie0_port {
> +	pcie@0,0 {
> +		pcie@2,0 {
> +			port {

The house that Jack built. Don't use multiple nested nodes to patch it.
The node might go away and nobody will notice it. Add a label to the
exact location and patch only it.

> +				pcie0_m2_e_ep: endpoint {
> +					remote-endpoint = <&m2_e_pcie_ep>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&uart4 {
> +	status = "okay";
> +	/delete-property/ interrupts;
> +	interrupts-extended = <&intc GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>,
> +			      <&tlmm 19 IRQ_TYPE_EDGE_FALLING>;
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-1 = <&qup_uart4_sleep_cts>, <&qup_uart4_sleep_rts>,
> +		    <&qup_uart4_sleep_tx>, <&qup_uart4_sleep_rx>;
> +
> +	port {
> +		uart4_m2_e_ep: endpoint {
> +			remote-endpoint = <&m2_e_uart_ep>;
> +		};
> +	};
> +};
> +
> +&uart7 {
> +	status = "disabled";
> +};
> +
> +&{/wcn6750-pmu} {

label

> +	status = "disabled";
> +};
> 
> -- 
> 2.34.1
> 

-- 
With best wishes
Dmitry