[PATCH v6 09/11] arm64: dts: qcom: ipq5210: Add I2C nodes

[Varadarajan Narayanan]

Add the QUPv3 I2C controller nodes for IPQ5210 and enable I2C0 with
the required pin configuration on RDP504.

Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@xxxxxxxxxxxxxxxx>
---
 .../arm64/boot/dts/qcom/ipq5210-rdp504-common.dtsi | 23 ++++++++++++
 arch/arm64/boot/dts/qcom/ipq5210.dtsi              | 42 ++++++++++++++++++++++
 2 files changed, 65 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq5210-rdp504-common.dtsi b/arch/arm64/boot/dts/qcom/ipq5210-rdp504-common.dtsi
index eceb6e0ca6fe..40926d1598e0 100644
--- a/arch/arm64/boot/dts/qcom/ipq5210-rdp504-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5210-rdp504-common.dtsi
@@ -59,6 +59,13 @@ vreg_misc_0p925: regulator-usb-0p925 {
 	};
 };
 
+&i2c0 {
+	pinctrl-0 = <&qup_i2c0_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
 &pcie0 {
 	pinctrl-0 = <&pcie0_default_state>;
 	pinctrl-names = "default";
@@ -195,6 +202,22 @@ clock-pins {
 		};
 	};
 
+	qup_i2c0_default: qup-i2c0-default-state {
+		qup-i2c0-scl-pins {
+			pins = "gpio20";
+			function = "qup_se2";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		qup-i2c0-sda-pins {
+			pins = "gpio21";
+			function = "qup_se2";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
 	qup_uart1_default_state: qup-uart1-default-state {
 		pins = "gpio38", "gpio39";
 		function = "qup_se1";
diff --git a/arch/arm64/boot/dts/qcom/ipq5210.dtsi b/arch/arm64/boot/dts/qcom/ipq5210.dtsi
index 6440853da8c3..50ce79219fe2 100644
--- a/arch/arm64/boot/dts/qcom/ipq5210.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5210.dtsi
@@ -427,6 +427,48 @@ uart1: serial@1a84000 {
 
 				status = "disabled";
 			};
+
+			i2c0: i2c@1a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x01a88000 0x0 0x4000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&gcc GCC_QUPV3_WRAP_SE2_CLK>;
+				clock-names = "se";
+				clock-frequency = <400000>;
+				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+				assigned-clocks = <&gcc GCC_QUPV3_WRAP_SE2_CLK>;
+				assigned-clock-rates = <32000000>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@1a8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x01a8c000 0x0 0x4000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&gcc GCC_QUPV3_WRAP_SE3_CLK>;
+				clock-names = "se";
+				clock-frequency = <400000>;
+				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+				assigned-clocks = <&gcc GCC_QUPV3_WRAP_SE3_CLK>;
+				assigned-clock-rates = <32000000>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@1a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x01a94000 0x0 0x4000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&gcc GCC_QUPV3_WRAP_SE5_CLK>;
+				clock-names = "se";
+				clock-frequency = <400000>;
+				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+				assigned-clocks = <&gcc GCC_QUPV3_WRAP_SE5_CLK>;
+				assigned-clock-rates = <32000000>;
+				status = "disabled";
+			};
 		};
 
 		sdhc: mmc@7804000 {

-- 
2.34.1