[PATCH 02/11] power: supply: qcom_smbx: Do not interfere with vbus driver

[David Heidelberg via B4 Relay]

From: David Heidelberg <david@xxxxxxx>

Charger should not touch bits handled by OTG block handled by the vbus
driver.

Signed-off-by: David Heidelberg <david@xxxxxxx>
---
 drivers/power/supply/qcom_smbx.c | 14 --------------
 1 file changed, 14 deletions(-)

diff --git a/drivers/power/supply/qcom_smbx.c b/drivers/power/supply/qcom_smbx.c
index 52bb5a6eb145d..9c071a79a16c2 100644
--- a/drivers/power/supply/qcom_smbx.c
+++ b/drivers/power/supply/qcom_smbx.c
@@ -96,28 +96,16 @@
 #define USBIN_ICL_CHANGE_RT_STS_BIT			BIT(6)
 #define USBIN_SOURCE_CHANGE_RT_STS_BIT			BIT(5)
 #define USBIN_PLUGIN_RT_STS_BIT				BIT(4)
 #define USBIN_OV_RT_STS_BIT				BIT(3)
 #define USBIN_UV_RT_STS_BIT				BIT(2)
 #define USBIN_LT_3P6V_RT_STS_BIT			BIT(1)
 #define USBIN_COLLAPSE_RT_STS_BIT			BIT(0)
 
-#define OTG_CFG						0x153
-#define OTG_RESERVED_MASK				GENMASK(7, 6)
-#define DIS_OTG_ON_TLIM_BIT				BIT(5)
-#define QUICKSTART_OTG_FASTROLESWAP_BIT			BIT(4)
-#define INCREASE_DFP_TIME_BIT				BIT(3)
-#define ENABLE_OTG_IN_DEBUG_MODE_BIT			BIT(2)
-#define OTG_EN_SRC_CFG_BIT				BIT(1)
-#define CONCURRENT_MODE_CFG_BIT				BIT(0)
-
-#define OTG_ENG_OTG_CFG					0x1C0
-#define ENG_BUCKBOOST_HALT1_8_MODE_BIT			BIT(0)
-
 #define APSD_STATUS					0x307
 #define APSD_STATUS_7_BIT				BIT(7)
 #define HVDCP_CHECK_TIMEOUT_BIT				BIT(6)
 #define SLOW_PLUGIN_TIMEOUT_BIT				BIT(5)
 #define ENUMERATION_DONE_BIT				BIT(4)
 #define VADP_CHANGE_DONE_AFTER_AUTH_BIT			BIT(3)
 #define QC_AUTH_DONE_STATUS_BIT				BIT(2)
 #define QC_CHARGER_BIT					BIT(1)
@@ -804,18 +792,16 @@ static const struct smb_init_register smb_init_seq[] = {
 	  .val = VCONN_EN_SRC_BIT },
 	/*
 	 * Disable Type-C factory mode and stay in Attached.SRC state when VCONN
 	 * over-current happens
 	 */
 	{ .addr = TYPE_C_CFG,
 	  .mask = FACTORY_MODE_DETECTION_EN_BIT | VCONN_OC_CFG_BIT,
 	  .val = 0 },
-	/* Configure VBUS for software control */
-	{ .addr = OTG_CFG, .mask = OTG_EN_SRC_CFG_BIT, .val = 0 },
 	/*
 	 * Use VBAT to determine the recharge threshold when battery is full
 	 * rather than the state of charge.
 	 */
 	{ .addr = FG_UPDATE_CFG_2_SEL,
 	  .mask = SOC_LT_CHG_RECHARGE_THRESH_SEL_BIT |
 		  VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT,
 	  .val = VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT },

-- 
2.55.0