[PATCH] arm64: dts: qcom: glymur-qcb: Add PCIe3a support

[Qiang Yu]

Add support for the PCIe3a x8 slot on the Glymur QCB board, wiring up its
regulators, pinctrl states, and PHY/port power supplies.

Signed-off-by: Qiang Yu <qiang.yu@xxxxxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/glymur-qcb.dts | 117 ++++++++++++++++++++++++++++++++
 1 file changed, 117 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/glymur-qcb.dts b/arch/arm64/boot/dts/qcom/glymur-qcb.dts
index 17d8ff3aed23..741a24454e80 100644
--- a/arch/arm64/boot/dts/qcom/glymur-qcb.dts
+++ b/arch/arm64/boot/dts/qcom/glymur-qcb.dts
@@ -78,6 +78,48 @@ vreg_nvme: regulator-nvme {
 		regulator-boot-on;
 	};
 
+	vreg_pcie_12v: regulator-pcie-12v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+
+		gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&pcie_x8_12v>;
+		pinctrl-names = "default";
+	};
+
+	vreg_pcie_3v3: regulator-pcie-3v3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 135 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&pm_main_3p3_en>;
+		pinctrl-names = "default";
+	};
+
+	vreg_pcie_3v3_aux: regulator-pcie-3v3-aux {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_3P3_AUX";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 136 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&pm_aux_3p3_en>;
+		pinctrl-names = "default";
+	};
+
 	vreg_wcn_0p95: regulator-wcn-0p95 {
 		compatible = "regulator-fixed";
 
@@ -438,6 +480,31 @@ embedded-controller@76 {
 	};
 };
 
+&pcie3a {
+	pinctrl-0 = <&pcie3a_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie3_phy {
+	vdda-phy-supply = <&vreg_l3c_e1_0p89>;
+	vdda-pll-supply = <&vreg_l2c_e1_1p14>;
+	vdda-refgen0p9-supply = <&vreg_l1c_e1_0p82>;
+	vdda-refgen1p2-supply = <&vreg_l4f_e1_1p08>;
+
+	status = "okay";
+};
+
+&pcie3a_port0 {
+	vpcie12v-supply = <&vreg_pcie_12v>;
+	vpcie3v3-supply = <&vreg_pcie_3v3>;
+	vpcie3v3aux-supply = <&vreg_pcie_3v3_aux>;
+
+	reset-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+};
+
 &pcie4 {
 	pinctrl-0 = <&pcie4_default>;
 	pinctrl-names = "default";
@@ -590,6 +657,29 @@ ec_int_n_default: ec-int-n-state {
 		bias-disable;
 	};
 
+	pcie3a_default: pcie3a-default-state {
+		clkreq-n-pins {
+			pins = "gpio144";
+			function = "pcie3a_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio143";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio145";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
 	pcie4_default: pcie4-default-state {
 		clkreq-n-pins {
 			pins = "gpio147";
@@ -659,6 +749,33 @@ wake-n-pins {
 		};
 	};
 
+	pcie_x8_12v: pcie-12v-default-state {
+		pins = "gpio26";
+		function = "gpio";
+		output-enable;
+		output-high;
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	pm_aux_3p3_en: pcie-aux-3p3-default-state {
+		pins = "gpio136";
+		function = "gpio";
+		output-enable;
+		output-high;
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	pm_main_3p3_en: pcie-main-3p3-default-state {
+		pins = "gpio135";
+		function = "gpio";
+		output-enable;
+		output-high;
+		drive-strength = <16>;
+		bias-disable;
+	};
+
 	wcn_wlan_bt_en: wcn-wlan-bt-en-state {
 		pins = "gpio116", "gpio117";
 		function = "gpio";

---
base-commit: 8b7179210b22f8e48a82c5ceacb9d56a9c4cfec4
change-id: 20261105-pcie3a_x8_1105-72b9c8dc1ee3

Best regards,
--  
Qiang Yu <qiang.yu@xxxxxxxxxxxxxxxx>