[PATCH 3/3] arm64: dts: qcom: add Monaco Draco EVK board
From: Faruque Ansari
Date: Mon Nov 16 2026 - 21:43:43 EST
The Monaco Draco EVK pairs the Monaco Draco AC SoM with the Draco
carrier board. Add its device tree, describing the board-specific
peripherals layered on top of the SoM:
- I2C GPIO expanders: 4x KTS1622 on i2c14 and 2x TCA9538 on i2c15
- EEPROM with a MAC-address nvmem layout on i2c15
- Native DisplayPort output (DP0)
- Gigabit Ethernet (ethernet0, 2500base-x) over an HSGMII PHY, with
the MAC address sourced from the EEPROM
- Dual PCIe (pcie0/pcie1) behind an on-board TC9563 PCIe switch
- ST33HTPM TPM over spi10
- AMC6821 fan controller on i2c13
- M.2 E-key slot connector and carrier debug UART (uart2)
Also hook the board dtb into the Makefile, together with an EL2
overlay variant that boots the kernel at EL2 for KVM.
Co-developed-by: Vishnu Saini <vishnu.saini@xxxxxxxxxxxxxxxx>
Signed-off-by: Vishnu Saini <vishnu.saini@xxxxxxxxxxxxxxxx>
Co-developed-by: Khalid Faisal Ansari <khalid.ansari@xxxxxxxxxxxxxxxx>
Signed-off-by: Khalid Faisal Ansari <khalid.ansari@xxxxxxxxxxxxxxxx>
Co-developed-by: Dipa Mantre <dipa.mantre@xxxxxxxxxxxxxxxx>
Signed-off-by: Dipa Mantre <dipa.mantre@xxxxxxxxxxxxxxxx>
Co-developed-by: Sravani Tella <tella@xxxxxxxxxxxxxxxxxxxxxxxxx>
Signed-off-by: Sravani Tella <tella@xxxxxxxxxxxxxxxxxxxxxxxxx>
Co-developed-by: Monish Chunara <monish.chunara@xxxxxxxxxxxxxxxx>
Signed-off-by: Monish Chunara <monish.chunara@xxxxxxxxxxxxxxxx>
Co-developed-by: Ajinkya Inchure <ainchure@xxxxxxxxxxxxxxxx>
Signed-off-by: Ajinkya Inchure <ainchure@xxxxxxxxxxxxxxxx>
Signed-off-by: Faruque Ansari <faruque.ansari@xxxxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/Makefile | 5 +
arch/arm64/boot/dts/qcom/monaco-draco-evk.dts | 546 ++++++++++++++++++++++++++
2 files changed, 551 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 88230c4e00ea..7212bd1d2358 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -69,6 +69,11 @@ dtb-$(CONFIG_ARCH_QCOM) += milos-fairphone-fp6.dtb
dtb-$(CONFIG_ARCH_QCOM) += milos-nothing-asteroids.dtb
dtb-$(CONFIG_ARCH_QCOM) += monaco-arduino-monza.dtb
dtb-$(CONFIG_ARCH_QCOM) += monaco-ac-evk.dtb
+dtb-$(CONFIG_ARCH_QCOM) += monaco-draco-evk.dtb
+
+monaco-draco-evk-el2-dtbs := monaco-draco-evk.dtb monaco-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += monaco-draco-evk-el2.dtb
+
dtb-$(CONFIG_ARCH_QCOM) += monaco-evk.dtb
monaco-evk-camera-imx577-dtbs := monaco-evk.dtb monaco-evk-camera-imx577.dtbo
diff --git a/arch/arm64/boot/dts/qcom/monaco-draco-evk.dts b/arch/arm64/boot/dts/qcom/monaco-draco-evk.dts
new file mode 100644
index 000000000000..ad416f586514
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/monaco-draco-evk.dts
@@ -0,0 +1,546 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pwm/pwm.h>
+
+#include "monaco-draco-ac-som.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. Monaco Draco EVK";
+ compatible = "qcom,monaco-draco-evk", "qcom,monaco-draco-ac-som",
+ "qcom,qcs8300";
+ chassis-type = "embedded";
+
+ aliases {
+ ethernet0 = ðernet0;
+ serial1 = &uart2;
+ };
+
+ vreg_0p9: regulator-0v9 {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_0P9";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vreg_1p8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_1P8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vreg_keye_3p3: regulator-keye-3p3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_keye_3p3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vreg_dp0_pwr: regulator-dp0-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_DP0_PWR_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&expander1 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ dp0-connector {
+ compatible = "dp-connector";
+ label = "DP0";
+ type = "full-size";
+ dp-pwr-supply = <&vreg_dp0_pwr>;
+
+ port {
+ dp0_connector_in: endpoint {
+ remote-endpoint = <&mdss_dp0_out>;
+ };
+ };
+ };
+
+ wifi-bt-connector {
+ compatible = "pcie-m2-e-connector";
+ vpcie3v3-supply = <&vreg_keye_3p3>;
+
+ w-disable2-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&bt_en>;
+ pinctrl-names = "default";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ m2_e_pcie_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tc9563_pcie1_ep>;
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ m2_e_uart_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&uart2_ep>;
+ };
+ };
+ };
+ };
+};
+
+ðernet0 {
+ phy-handle = <&hsgmii_phy0>;
+ phy-mode = "2500base-x";
+
+ pinctrl-0 = <ðernet0_default>;
+ pinctrl-names = "default";
+
+ snps,mtl-rx-config = <&mtl_rx_setup>;
+ snps,mtl-tx-config = <&mtl_tx_setup>;
+
+ nvmem-cells = <&mac_addr0>;
+ nvmem-cell-names = "mac-address";
+
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hsgmii_phy0: ethernet-phy@1c {
+ compatible = "ethernet-phy-id004d.d101";
+ reg = <0x1c>;
+ reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <11000>;
+ reset-deassert-us = <70000>;
+ };
+ };
+
+ mtl_rx_setup: rx-queues-config {
+ snps,rx-queues-to-use = <4>;
+ snps,rx-sched-sp;
+
+ queue0 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x0>;
+ snps,route-up;
+ snps,priority = <0x1>;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x1>;
+ snps,route-ptp;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x2>;
+ snps,route-avcp;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x3>;
+ snps,priority = <0xc>;
+ };
+ };
+
+ mtl_tx_setup: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+
+ queue0 {
+ snps,dcb-algorithm;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+ };
+};
+
+&i2c13 {
+ status = "okay";
+
+ fan_controller: fan@1a {
+ compatible = "ti,amc6821";
+ reg = <0x1a>;
+ #pwm-cells = <2>;
+
+ fan {
+ pwms = <&fan_controller 40000 PWM_POLARITY_INVERTED>;
+ };
+ };
+};
+
+&i2c14 {
+ status = "okay";
+
+ expander0: gpio@20 {
+ compatible = "kinetic,kts1622", "ti,tcal6416";
+ reg = <0x20>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ expander1: gpio@21 {
+ compatible = "kinetic,kts1622", "ti,tcal6416";
+ reg = <0x21>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ expander2: gpio@22 {
+ compatible = "kinetic,kts1622", "ti,tcal6416";
+ reg = <0x22>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ expander3: gpio@23 {
+ compatible = "kinetic,kts1622", "ti,tcal6416";
+ reg = <0x23>;
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ pwr-en0-hog {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "pwr_en0";
+ };
+
+ pwr-en1-hog {
+ gpio-hog;
+ gpios = <1 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "pwr_en1";
+ };
+
+ pwr-en4-hog {
+ gpio-hog;
+ gpios = <4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "pwr_en4";
+ };
+
+ pwr-en6-hog {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "pwr_en6";
+ };
+
+ pwr-en8-hog {
+ gpio-hog;
+ gpios = <8 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "pwr_en8";
+ };
+
+ keye-pwr-en1-hog {
+ gpio-hog;
+ gpios = <9 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "keye_pwr_en1";
+ };
+
+ keye-pwr-en2-hog {
+ gpio-hog;
+ gpios = <10 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "keye_pwr_en2";
+ };
+ };
+};
+
+&i2c15 {
+ status = "okay";
+
+ expander4: gpio@38 {
+ compatible = "ti,tca9538";
+ reg = <0x38>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ expander5: gpio@3c {
+ compatible = "ti,tca9538";
+ reg = <0x3c>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ eeprom@50 {
+ compatible = "giantec,gt24c256c", "atmel,24c256";
+ reg = <0x50>;
+ pagesize = <64>;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mac_addr0: mac-addr@0 {
+ reg = <0x0 0x6>;
+ };
+ };
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp0 {
+ pinctrl-0 = <&dp_hot_plug_det>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+ remote-endpoint = <&dp0_connector_in>;
+};
+
+&pcie0 {
+ perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+
+ iommu-map = <0x0 &pcie_smmu 0x0 0x0 0x1>,
+ <0x100 &pcie_smmu 0x1 0x0 0x1>,
+ <0x208 &pcie_smmu 0x2 0x0 0x1>,
+ <0x210 &pcie_smmu 0x3 0x0 0x1>,
+ <0x218 &pcie_smmu 0x4 0x0 0x1>,
+ <0x300 &pcie_smmu 0x5 0x0 0x1>,
+ <0x400 &pcie_smmu 0x6 0x0 0x1>,
+ <0x500 &pcie_smmu 0x7 0x0 0x1>,
+ <0x501 &pcie_smmu 0x8 0x0 0x1>;
+
+ status = "okay";
+};
+
+&pcie1 {
+ perst-gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pcie1_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcieport0 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ pcie@0,0 {
+ compatible = "pci1179,0623";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x2 0xff>;
+
+ vddc-supply = <&vreg_0p9>;
+ vdd18-supply = <&vreg_1p8>;
+ vdd09-supply = <&vreg_0p9>;
+ vddio1-supply = <&vreg_1p8>;
+ vddio2-supply = <&vreg_1p8>;
+ vddio18-supply = <&vreg_1p8>;
+ i2c-parent = <&i2c15 0x77>;
+ resx-gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&tc9563_resx_n>;
+ pinctrl-names = "default";
+
+ pcie@1,0 {
+ reg = <0x20800 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x3 0xff>;
+
+ port {
+ tc9563_pcie1_ep: endpoint {
+ remote-endpoint = <&m2_e_pcie_ep>;
+ };
+ };
+ };
+
+ pcie@2,0 {
+ reg = <0x21000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x4 0xff>;
+ };
+
+ pcie@3,0 {
+ reg = <0x21800 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x5 0xff>;
+
+ pcie@0,0 {
+ reg = <0x50000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ };
+
+ pcie@0,1 {
+ reg = <0x50100 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ };
+ };
+ };
+};
+
+&qup_i2c13_data_clk {
+ drive-strength = <6>;
+ bias-pull-up;
+};
+
+&spi10 {
+ status = "okay";
+
+ tpm@0 {
+ compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&tlmm {
+ bt_en: bt-en-state {
+ pins = "gpio55";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ ethernet0_default: ethernet0-default-state {
+ ethernet0_mdc: ethernet0-mdc-pins {
+ pins = "gpio5";
+ function = "emac0_mdc";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ ethernet0_mdio: ethernet0-mdio-pins {
+ pins = "gpio6";
+ function = "emac0_mdio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+
+ pcie0_default_state: pcie0-default-state {
+ clkreq-pins {
+ pins = "gpio1";
+ function = "pcie0_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-pins {
+ pins = "gpio2";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ wake-pins {
+ pins = "gpio0";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie1_default_state: pcie1-default-state {
+ clkreq-pins {
+ pins = "gpio22";
+ function = "pcie1_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-pins {
+ pins = "gpio23";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ wake-pins {
+ pins = "gpio21";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ tc9563_resx_n: tc9563-resx-state {
+ pins = "gpio96";
+ function = "gpio";
+ bias-disable;
+ output-high;
+ };
+};
+
+&uart2 {
+ status = "okay";
+
+ port {
+ uart2_ep: endpoint {
+ remote-endpoint = <&m2_e_uart_ep>;
+ };
+ };
+};
--
2.34.1