Re: [PATCH v2 2/2] riscv: dts: thead: Enable bluetooth on BeagleV-Ahead

From: Thomas Gerner

Date: Sat Nov 21 2026 - 06:09:45 EST


Am 21.11.26 um 00:34 schrieb Drew Fustini:
On Tue, Oct 20, 2026 at 03:26:04PM +0200, Thomas Gerner wrote:
On the BeagleV-Ahead the bluetooth module of the Ampak AP6203BM is
identified by the btbcm driver as BCM4362A2. The module is connected by
UART4, several gpio pins and an I2S interface. The I2S is currently not
used as there is currently no driver.

Signed-off-by: Thomas Gerner <thomas.gerner@xxxxxxxxxxxxxxxx>
---
Changes in v2:
- use default pinctrl definition for bluetooth in and out pins
Thanks for sending v2. Sorry for the delay in review.


.../boot/dts/thead/th1520-beaglev-ahead.dts | 85 +++++++++++++++++++
1 file changed, 85 insertions(+)

diff --git a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
index e16484a47653..7161a9d4c61f 100644
--- a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
+++ b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
@@ -76,6 +76,23 @@ led-5 {
};
};
+ reg_vbat_1v8: regulator-vbat-1v8 {
+ compatible = "regulator-fixed";
+ regulator-boot-on;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "vbat-1v8";
+ };
+
+ reg_vbat_3v3: regulator-vbat-3v3 {
+ compatible = "regulator-fixed";
+ enable-active-high;
enable-active-high has no effect without a gpio.

+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "vbat-3v3";
+ };
Nothing can switch these two rails so regulator-always-on describes them
better than regulator-boot-on.


I see. With the next version I will consider this. The regulator definitions are here only to
prevent the hci driver form printing a message about missing regulator. Once we have
the final regulators for the AON subsystem we should check this definitions and replace
them if appropriate.


+
hdmi-connector {
compatible = "hdmi-connector";
type = "d";
@@ -152,6 +169,28 @@ led-pins {
};
&padctrl0_apsys {
+ bluetooth_pins: bluetooth-0 {
+ in-pins {
+ bias-disable;
+ drive-strength = <1>;
+ function = "gpio";
+ input-enable;
+ input-schmitt-enable;
+ pins = "GPIO2_30";
+ slew-rate = <0>;
+ };
+
+ out-pins {
+ bias-disable;
+ drive-strength = <3>;
+ input-disable;
+ input-schmitt-disable;
+ pins = "SDIO1_DETN", /* GPIO2_29 */
+ "SDIO1_WPRTN"; /* GPIO2_28 */
+ slew-rate = <0>;
+ };
+ };
+
gmac0_pins: gmac0-0 {
tx-pins {
pins = "GMAC0_TX_CLK",
@@ -268,6 +307,30 @@ reg-on-pins {
};
};
+&padctrl1_apsys {
+ uart4_pins: uart4-0 {
+ rx-pins {
+ bias-disable;
+ drive-strength = <1>;
+ function = "uart";
+ input-enable;
+ pins = "UART4_RXD", "UART4_CTSN";
+ input-schmitt-enable;
+ slew-rate = <0>;
+ };
+
+ tx-pins {
+ bias-disable;
+ drive-strength = <3>;
+ function = "uart";
+ input-disable;
+ pins = "UART4_TXD", "UART4_RTSN";
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+ };
+};
+
&sdio0 {
bus-width = <4>;
max-frequency = <198000000>;
@@ -314,3 +377,25 @@ &uart0 {
pinctrl-0 = <&uart0_pins>;
status = "okay";
};
+
+&uart4 {
+ pinctrl-0 = <&uart4_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4329-bt";
+ device-wakeup-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <30 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "host-wakeup";
+ max-speed = <921600>;
+ pinctrl-0 = <&bluetooth_pins>;
+ pinctrl-names = "default";
+ shutdown-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* BT-REG-ON */
This triggers checkpatch:

WARNING: please, no space before tabs
#230: FILE: arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts:397:
+^I^Ishutdown-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>; ^I/* BT-REG-ON */$

+ vbat-supply = <&reg_vbat_3v3>;
+ vddio-supply = <&reg_vbat_1v8>;
+ };
+};
--
2.53.0

Thanks,
Drew


Best regards
Thomas