[PATCHv2] staging: rtl8192u: checkpatch: do not use C99 // comments
From: Martin Kepplinger
Date: Sun Aug 10 2014 - 09:17:11 EST
Use the common kernel coding style, so don't use C99 // comments
in r8192U_core.c If too long, where reasonable, they are shortened
as well.
Some old internal comments about date and author of changes are
removed.
This provides a more consistent view and hopefully encourages to
look at it.
Signed-off-by: Martin Kepplinger <martink@xxxxxxxxx>
---
Yes, there were changes in the meantime. This applies to -next20140808
and builds. thanks.
drivers/staging/rtl8192u/r8192U_core.c | 757 +++++++++++++++++---------------
1 file changed, 408 insertions(+), 349 deletions(-)
diff --git a/drivers/staging/rtl8192u/r8192U_core.c b/drivers/staging/rtl8192u/r8192U_core.c
index 7640386..f97019d 100644
--- a/drivers/staging/rtl8192u/r8192U_core.c
+++ b/drivers/staging/rtl8192u/r8192U_core.c
@@ -87,7 +87,7 @@ double __extendsfdf2(float a)
#include "r8190_rtl8256.h" /* RTL8225 Radio frontend */
#include "r8180_93cx6.h" /* Card EEPROM */
#include "r8192U_wx.h"
-#include "r819xU_phy.h" //added by WB 4.30.2008
+#include "r819xU_phy.h"
#include "r819xU_phyreg.h"
#include "r819xU_cmdpkt.h"
#include "r8192U_dm.h"
@@ -95,13 +95,13 @@ double __extendsfdf2(float a)
#include <linux/slab.h>
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
-// FIXME: check if 2.6.7 is ok
+/* FIXME: check if 2.6.7 is ok */
#include "dot11d.h"
-//set here to open your trace code. //WB
+/* set here to open your trace code. */
u32 rt_global_debug_component = COMP_DOWN |
COMP_SEC |
- COMP_ERR; //always open err flags on
+ COMP_ERR; /* always open err flags on */
#define TOTAL_CAM_ENTRY 32
#define CAM_CONTENT_COUNT 8
@@ -132,7 +132,7 @@ MODULE_DEVICE_TABLE(usb, rtl8192_usb_id_tbl);
MODULE_DESCRIPTION("Linux driver for Realtek RTL8192 USB WiFi cards");
static char *ifname = "wlan%d";
-static int hwwep = 1; //default use hw. set 0 to use software security
+static int hwwep = 1; /* default use hw. set 0 to use software security */
static int channels = 0x3fff;
@@ -166,17 +166,17 @@ typedef struct _CHANNEL_LIST {
} CHANNEL_LIST, *PCHANNEL_LIST;
static CHANNEL_LIST ChannelPlan[] = {
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165}, 24}, //FCC
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11}, 11}, //IC
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64}, 21}, //ETSI
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13}, 13}, //Spain. Change to ETSI.
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13}, 13}, //France. Change to ETSI.
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 36, 40, 44, 48, 52, 56, 60, 64}, 22}, //MKK //MKK
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 36, 40, 44, 48, 52, 56, 60, 64}, 22},//MKK1
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13}, 13}, //Israel.
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 36, 40, 44, 48, 52, 56, 60, 64}, 22}, // For 11a , TELEC
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 36, 40, 44, 48, 52, 56, 60, 64}, 22}, //MIC
- {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14}, 14} //For Global Domain. 1-11:active scan, 12-14 passive scan. //+YJ, 080626
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165}, 24}, /* FCC */
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11}, 11}, /* IC */
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64}, 21}, /* ETSI */
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13}, 13}, /* Spain. Change to ETSI. */
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13}, 13}, /* France. Change to ETSI. */
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 36, 40, 44, 48, 52, 56, 60, 64}, 22}, /* MKK */
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 36, 40, 44, 48, 52, 56, 60, 64}, 22}, /* MKK1 */
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13}, 13}, /* Israel. */
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 36, 40, 44, 48, 52, 56, 60, 64}, 22}, /* For 11a , TELEC */
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 36, 40, 44, 48, 52, 56, 60, 64}, 22}, /* MIC */
+ {{1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14}, 14} /* For Global Domain. 1-11:active scan, 12-14 passive scan.*/
};
static void rtl819x_set_channel_map(u8 channel_plan, struct r8192_priv *priv)
@@ -196,7 +196,7 @@ static void rtl819x_set_channel_map(u8 channel_plan, struct r8192_priv *priv)
case COUNTRY_CODE_MIC:
Dot11d_Init(ieee);
ieee->bGlobalDomain = false;
- //actually 8225 & 8256 rf chips only support B,G,24N mode
+ /* actually 8225 & 8256 rf chips only support B,G,24N mode */
if ((priv->rf_chip == RF_8225) || (priv->rf_chip == RF_8256)) {
min_chan = 1;
max_chan = 14;
@@ -204,9 +204,9 @@ static void rtl819x_set_channel_map(u8 channel_plan, struct r8192_priv *priv)
RT_TRACE(COMP_ERR, "unknown rf chip, can't set channel map in function:%s()\n", __func__);
}
if (ChannelPlan[channel_plan].Len != 0) {
- // Clear old channel map
+ /* Clear old channel map */
memset(GET_DOT11D_INFO(ieee)->channel_map, 0, sizeof(GET_DOT11D_INFO(ieee)->channel_map));
- // Set new channel map
+ /* Set new channel map */
for (i = 0; i < ChannelPlan[channel_plan].Len; i++) {
if (ChannelPlan[channel_plan].Channel[i] < min_chan || ChannelPlan[channel_plan].Channel[i] > max_chan)
break;
@@ -216,7 +216,9 @@ static void rtl819x_set_channel_map(u8 channel_plan, struct r8192_priv *priv)
break;
case COUNTRY_CODE_GLOBAL_DOMAIN:
- GET_DOT11D_INFO(ieee)->bEnabled = 0;//this flag enabled to follow 11d country IE setting, otherwise, it shall follow global domain settings.
+ /* this flag enabled to follow 11d country IE setting,
+ * otherwise, it shall follow global domain settings. */
+ GET_DOT11D_INFO(ieee)->bEnabled = 0;//
Dot11d_Reset(ieee);
ieee->bGlobalDomain = true;
break;
@@ -232,12 +234,14 @@ static void rtl819x_set_channel_map(u8 channel_plan, struct r8192_priv *priv)
static void CamResetAllEntry(struct net_device *dev)
{
u32 ulcommand = 0;
- //2004/02/11 In static WEP, OID_ADD_KEY or OID_ADD_WEP are set before STA associate to AP.
- // However, ResetKey is called on OID_802_11_INFRASTRUCTURE_MODE and MlmeAssociateRequest
- // In this condition, Cam can not be reset because upper layer will not set this static key again.
+ /* In static WEP, OID_ADD_KEY or OID_ADD_WEP are set before STA
+ * associate to AP. However, ResetKey is called on
+ * OID_802_11_INFRASTRUCTURE_MODE and MlmeAssociateRequest
+ * In this condition, Cam can not be reset because upper layer
+ * will not set this static key again.
+ */
ulcommand |= BIT31|BIT30;
write_nic_dword(dev, RWCAM, ulcommand);
-
}
@@ -287,7 +291,7 @@ int read_nic_byte_E(struct net_device *dev, int indx, u8 *data)
return 0;
}
-//as 92U has extend page from 4 to 16, so modify functions below.
+/* as 92U has extend page from 4 to 16, so modify functions below. */
void write_nic_byte(struct net_device *dev, int indx, u8 data)
{
int status;
@@ -712,7 +716,7 @@ void rtl8192_set_chan(struct net_device *dev, short ch)
/* this hack should avoid frame TX during channel setting*/
#ifndef LOOP_TEST
- //need to implement rf set channel here WB
+ /* need to implement rf set channel here WB */
if (priv->rf_set_chan)
priv->rf_set_chan(dev, priv->chan);
@@ -758,7 +762,7 @@ static int rtl8192_rx_initiate(struct net_device *dev)
info = (struct rtl8192_rx_info *) skb->cb;
info->urb = entry;
info->dev = dev;
- info->out_pipe = 3; //denote rx normal packet queue
+ info->out_pipe = 3; /* denote rx normal packet queue */
skb_queue_tail(&priv->rx_queue, skb);
usb_submit_urb(entry, GFP_KERNEL);
}
@@ -779,7 +783,7 @@ static int rtl8192_rx_initiate(struct net_device *dev)
info = (struct rtl8192_rx_info *) skb->cb;
info->urb = entry;
info->dev = dev;
- info->out_pipe = 9; //denote rx cmd packet queue
+ info->out_pipe = 9; /* denote rx cmd packet queue */
skb_queue_tail(&priv->rx_queue, skb);
usb_submit_urb(entry, GFP_KERNEL);
}
@@ -829,7 +833,7 @@ void rtl8192_set_rxconf(struct net_device *dev)
write_nic_dword(dev, RCR, rxconf);
}
-//wait to be removed
+/* wait to be removed */
void rtl8192_rx_enable(struct net_device *dev)
{
rtl8192_rx_initiate(dev);
@@ -975,13 +979,13 @@ static u32 rtl819xusb_rx_command_packet(struct net_device *dev,
static void rtl8192_data_hard_stop(struct net_device *dev)
{
- //FIXME !!
+ /* FIXME !! */
}
static void rtl8192_data_hard_resume(struct net_device *dev)
{
- // FIXME !!
+ /* FIXME !! */
}
/* this function TX data frames when the ieee80211 stack requires this.
@@ -1068,9 +1072,9 @@ struct sk_buff *DrvAggr_Aggregation(struct net_device *dev, struct ieee80211_drv
tx_desc_819x_usb_aggr_subframe *tx_agg_desc = NULL;
tx_fwinfo_819x_usb *tx_fwinfo = NULL;
- //
- // Local variable initialization.
- //
+ /*
+ * Local variable initialization.
+ */
/* first skb initialization */
skb = pSendList->tx_agg_frames[0];
TotalLength = skb->len;
@@ -1089,7 +1093,8 @@ struct sk_buff *DrvAggr_Aggregation(struct net_device *dev, struct ieee80211_drv
memset(agg_skb->data, 0, agg_skb->len);
skb_reserve(agg_skb, ieee->tx_headroom);
- /* reserve info for first subframe Tx descriptor to be set in the tx function */
+ /* reserve info for first subframe Tx descriptor to be set
+ * in the tx function */
skb = pSendList->tx_agg_frames[0];
tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE);
tcb_desc->drv_agg_enable = 1;
@@ -1119,7 +1124,8 @@ struct sk_buff *DrvAggr_Aggregation(struct net_device *dev, struct ieee80211_drv
tx_fwinfo->AllowAggregation = 1;
/* DWORD 1 */
tx_fwinfo->RxMF = tcb_desc->ampdu_factor;
- tx_fwinfo->RxAMD = tcb_desc->ampdu_density&0x07;//ampdudensity
+ /* ampdudensity */
+ tx_fwinfo->RxAMD = tcb_desc->ampdu_density&0x07;
} else {
tx_fwinfo->AllowAggregation = 0;
/* DWORD 1 */
@@ -1142,7 +1148,8 @@ struct sk_buff *DrvAggr_Aggregation(struct net_device *dev, struct ieee80211_drv
if (priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20_40) {
if (tcb_desc->bPacketBW) {
tx_fwinfo->TxBandwidth = 1;
- tx_fwinfo->TxSubCarrier = 0; //By SD3's Jerry suggestion, use duplicated mode
+ /* use duplicated mode */
+ tx_fwinfo->TxSubCarrier = 0;
} else {
tx_fwinfo->TxBandwidth = 0;
tx_fwinfo->TxSubCarrier = priv->nCur40MhzPrimeSC;
@@ -1195,7 +1202,7 @@ struct sk_buff *DrvAggr_Aggregation(struct net_device *dev, struct ieee80211_drv
tx_agg_desc->OWN = 1;
- //DWORD 2
+ /*DWORD 2*/
/* According windows driver, it seems that there no need to fill this field */
/* to fill next packet */
@@ -1263,16 +1270,16 @@ static void rtl8192_tx_isr(struct urb *tx_urb)
atomic_dec(&priv->tx_pending[queue_index]);
}
- //
- // Handle HW Beacon:
- // We had transfer our beacon frame to host controller at this moment.
- //
- //
- // Caution:
- // Handling the wait queue of command packets.
- // For Tx command packets, we must not do TCB fragment because it is not handled right now.
- // We must cut the packets to match the size of TX_CMD_PKT before we send it.
- //
+ /*
+ * Handle HW Beacon:
+ * We had transfer our beacon frame to host controller at this moment.
+ *
+ * Caution:
+ * Handling the wait queue of command packets.
+ * For Tx command packets, we must not do TCB fragment because it is
+ * not handled right now. We must cut the packets to match the size of
+ * TX_CMD_PKT before we send it.
+ */
/* Handle MPDU in wait queue. */
if (queue_index != BEACON_QUEUE) {
@@ -1283,12 +1290,12 @@ static void rtl8192_tx_isr(struct urb *tx_urb)
if (skb)
priv->ieee80211->softmac_hard_start_xmit(skb, dev);
- return; //modified by david to avoid further processing AMSDU
+ return; /* modified to avoid further processing AMSDU */
}
#ifdef USB_TX_DRIVER_AGGREGATION_ENABLE
else if ((skb_queue_len(&priv->ieee80211->skb_drv_aggQ[queue_index]) != 0) &&
(!(priv->ieee80211->queue_stop))) {
- // Tx Driver Aggregation process
+ /* Tx Driver Aggregation process */
/* The driver will aggregation the packets according to the following stats
* 1. check whether there's tx irq available, for it's a completion return
* function, it should contain enough tx irq;
@@ -1430,7 +1437,7 @@ static void rtl8192_update_cap(struct net_device *dev, u16 cap)
u8 slot_time = 0;
if ((cap & WLAN_CAPABILITY_SHORT_SLOT) && (!priv->ieee80211->pHTInfo->bCurrentRT2RTLongSlotTime)) /* short slot time */
slot_time = SHORT_SLOT_TIME;
- else //long slot time
+ else /* long slot time */
slot_time = NON_SHORT_SLOT_TIME;
priv->slot_time = slot_time;
write_nic_byte(dev, SLOT_TIME, slot_time);
@@ -1460,7 +1467,7 @@ static void rtl8192_net_update(struct net_device *dev)
write_nic_word(dev, BCN_DRV_EARLY_INT, 1);
write_nic_byte(dev, BCN_ERR_THRESH, 100);
BcnTimeCfg |= (BcnCW<<BCN_TCFG_CW_SHIFT);
- // TODO: BcnIFS may required to be changed on ASIC
+ /* TODO: BcnIFS may required to be changed on ASIC */
BcnTimeCfg |= BcnIFS<<BCN_TCFG_IFS;
write_nic_word(dev, BCN_TCFG, BcnTimeCfg);
@@ -1470,8 +1477,7 @@ static void rtl8192_net_update(struct net_device *dev)
}
-//temporary hw beacon is not used any more.
-//open it when necessary
+/* temporary hw beacon is not used any more. open it when necessary */
void rtl819xusb_beacon_tx(struct net_device *dev, u16 tx_rate)
{
@@ -1496,11 +1502,11 @@ u16 ComputeTxTime(u16 FrameLength, u16 DataRate, u8 bManagementFrame,
if (rtl8192_IsWirelessBMode(DataRate)) {
if (bManagementFrame || !bShortPreamble || DataRate == 10) /* long preamble */
FrameTime = (u16)(144+48+(FrameLength*8/(DataRate/10)));
- else // Short preamble
+ else /* Short preamble */
FrameTime = (u16)(72+24+(FrameLength*8/(DataRate/10)));
if ((FrameLength*8 % (DataRate/10)) != 0) /* Get the Ceilling */
FrameTime++;
- } else { //802.11g DSSS-OFDM PLCP length field calculation.
+ } else { /* 802.11g DSSS-OFDM PLCP length field calculation. */
N_DBPS = N_DBPSOfRate(DataRate);
Ceiling = (16 + 8*FrameLength + 6) / N_DBPS
+ (((16 + 8*FrameLength + 6) % N_DBPS) ? 1 : 0);
@@ -1581,17 +1587,17 @@ short rtl819xU_tx_cmd(struct net_device *dev, struct sk_buff *skb)
memset(pdesc, 0, USB_HWDESC_HEADER_LEN);
/* Tx descriptor ought to be set according to the skb->cb */
- pdesc->FirstSeg = 1;//bFirstSeg;
- pdesc->LastSeg = 1;//bLastSeg;
+ pdesc->FirstSeg = 1; /* bFirstSeg; */
+ pdesc->LastSeg = 1; /* bLastSeg; */
pdesc->CmdInit = tcb_desc->bCmdOrInit;
pdesc->TxBufferSize = tcb_desc->txbuf_size;
pdesc->OWN = 1;
pdesc->LINIP = tcb_desc->bLastIniPkt;
- //----------------------------------------------------------------------------
- // Fill up USB_OUT_CONTEXT.
- //----------------------------------------------------------------------------
- // Get index to out pipe from specified QueueID.
+ /*----------------------------------------------------------------------
+ * Fill up USB_OUT_CONTEXT.
+ *--------------------------------------------------------------------*/
+ /* Get index to out pipe from specified QueueID. */
#ifndef USE_ONE_PIPE
idx_pipe = txqueue2outpipe(priv, queue_index);
#else
@@ -1619,7 +1625,7 @@ short rtl819xU_tx_cmd(struct net_device *dev, struct sk_buff *skb)
*/
static u8 MapHwQueueToFirmwareQueue(u8 QueueID)
{
- u8 QueueSelect = 0x0; //defualt set to
+ u8 QueueSelect = 0x0; /*defualt set to*/
switch (QueueID) {
case BE_QUEUE:
@@ -1645,8 +1651,8 @@ static u8 MapHwQueueToFirmwareQueue(u8 QueueID)
QueueSelect = QSLT_BEACON;
break;
- // TODO: 2006.10.30 mark other queue selection until we verify it is OK
- // TODO: Remove Assertions
+ /* TODO: mark other queue selection until we verify it is OK */
+ /* TODO: Remove Assertions */
case TXCMD_QUEUE:
QueueSelect = QSLT_CMD;
break;
@@ -1703,7 +1709,7 @@ static u8 MRateToHwRate8190Pci(u8 rate)
ret = DESC90_RATE54M;
break;
- // HT rate since here
+ /* HT rate since here */
case MGN_MCS0:
ret = DESC90_RATEMCS0;
break;
@@ -1824,7 +1830,7 @@ short rtl8192_tx(struct net_device *dev, struct sk_buff *skb)
tx_fwinfo->AllowAggregation = 1;
/* DWORD 1 */
tx_fwinfo->RxMF = tcb_desc->ampdu_factor;
- tx_fwinfo->RxAMD = tcb_desc->ampdu_density&0x07;//ampdudensity
+ tx_fwinfo->RxAMD = tcb_desc->ampdu_density&0x07;/*ampdudensity*/
} else {
tx_fwinfo->AllowAggregation = 0;
/* DWORD 1 */
@@ -1847,7 +1853,7 @@ short rtl8192_tx(struct net_device *dev, struct sk_buff *skb)
if (priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20_40) {
if (tcb_desc->bPacketBW) {
tx_fwinfo->TxBandwidth = 1;
- tx_fwinfo->TxSubCarrier = 0; //By SD3's Jerry suggestion, use duplicated mode
+ tx_fwinfo->TxSubCarrier = 0; /* use duplicated mode */
} else {
tx_fwinfo->TxBandwidth = 0;
tx_fwinfo->TxSubCarrier = priv->nCur40MhzPrimeSC;
@@ -1911,7 +1917,7 @@ short rtl8192_tx(struct net_device *dev, struct sk_buff *skb)
tx_desc->USERATE = tcb_desc->bTxUseDriverAssingedRate;
/* Fill fields that are required to be initialized in all of the descriptors */
- //DWORD 0
+ /*DWORD 0*/
tx_desc->FirstSeg = 1;
tx_desc->LastSeg = 1;
tx_desc->OWN = 1;
@@ -1922,7 +1928,7 @@ short rtl8192_tx(struct net_device *dev, struct sk_buff *skb)
} else
#endif
{
- //DWORD 2
+ /*DWORD 2*/
tx_desc->TxBufferSize = (u32)(skb->len - USB_HWDESC_HEADER_LEN);
}
/* Get index to out pipe from specified QueueID */
@@ -1939,7 +1945,11 @@ short rtl8192_tx(struct net_device *dev, struct sk_buff *skb)
status = usb_submit_urb(tx_urb, GFP_ATOMIC);
if (!status) {
- //we need to send 0 byte packet whenever 512N bytes/64N(HIGN SPEED/NORMAL SPEED) bytes packet has been transmitted. Otherwise, it will be halt to wait for another packet. WB. 2008.08.27
+ /* we need to send 0 byte packet whenever
+ * 512N bytes/64N(HIGN SPEED/NORMAL SPEED) bytes packet has
+ * been transmitted. Otherwise, it will be halt to wait for
+ * another packet.
+ */
bool bSend0Byte = false;
u8 zero = 0;
if (udev->speed == USB_SPEED_HIGH) {
@@ -2093,7 +2103,10 @@ static void rtl8192_link_change(struct net_device *dev)
if (ieee->state == IEEE80211_LINKED) {
rtl8192_net_update(dev);
rtl8192_update_ratr_table(dev);
- //add this as in pure N mode, wep encryption will use software way, but there is no chance to set this as wep will not set group key in wext. WB.2008.07.08
+ /* add this as in pure N mode, wep encryption will use software
+ * way, but there is no chance to set this as wep will not set
+ * group key in wext.
+ */
if ((KEY_TYPE_WEP40 == ieee->pairwise_key_type) || (KEY_TYPE_WEP104 == ieee->pairwise_key_type))
EnableHWSecurityConfig8192(dev);
}
@@ -2152,7 +2165,7 @@ static void rtl8192_qos_activate(struct work_struct *work)
/* For we just support b/g mode at present, let the slot time at 9/20 selection */
/* update the ac parameter to related registers */
for (i = 0; i < QOS_QUEUE_NUM; i++) {
- //Mode G/A: slotTimeTimer = 9; Mode B: 20
+ /* Mode G/A: slotTimeTimer = 9; Mode B: 20 */
u1bAIFS = qos_parameters->aifs[i] * ((mode&(IEEE_G|IEEE_N_24G)) ? 9 : 20) + aSifsTime;
u4bAcParam = ((((u32)(qos_parameters->tx_op_limit[i]))<< AC_PARAM_TXOP_LIMIT_OFFSET)|
(((u32)(qos_parameters->cw_max[i]))<< AC_PARAM_ECW_MAX_OFFSET)|
@@ -2339,7 +2352,9 @@ static bool GetNmodeSupportBySecCfg8192(struct net_device *dev)
int encrypt;
crypt = ieee->crypt[ieee->tx_keyidx];
- //we use connecting AP's capability instead of only security config on our driver to distinguish whether it should use N mode or G mode
+ /* we use connecting AP's capability instead of only security config on
+ * our driver to distinguish whether it should use N mode or G mode
+ */
encrypt = (network->capability & WLAN_CAPABILITY_PRIVACY) || (ieee->host_encrypt && crypt && crypt->ops && (0 == strcmp(crypt->ops->name, "WEP")));
/* simply judge */
@@ -2376,7 +2391,8 @@ static bool GetHalfNmodeSupportByAPs819xUsb(struct net_device *dev)
static void rtl8192_refresh_supportrate(struct r8192_priv *priv)
{
struct ieee80211_device *ieee = priv->ieee80211;
- //we do not consider set support rate for ABG mode, only HT MCS rate is set here.
+ /* we do not consider set support rate for ABG mode, only HT MCS rate
+ * is set here. */
if (ieee->mode == WIRELESS_MODE_N_24G || ieee->mode == WIRELESS_MODE_N_5G)
memcpy(ieee->Regdot11HTOperationalRateSet, ieee->RegHTSuppRateSet, 16);
else
@@ -2424,7 +2440,9 @@ static void rtl8192_SetWirelessMode(struct net_device *dev, u8 wireless_mode)
wireless_mode = WIRELESS_MODE_B;
}
}
-#ifdef TO_DO_LIST //// TODO: this function doesn't work well at this time, we should wait for FPGA
+#ifdef TO_DO_LIST
+ /* TODO: this function doesn't work well at this time,
+ * we should wait for FPGA */
ActUpdateChannelAccessSetting(pAdapter, pHalData->CurrentWirelessMode, &pAdapter->MgntInfo.Info8185.ChannelAccessSetting);
#endif
priv->ieee80211->mode = wireless_mode;
@@ -2437,43 +2455,43 @@ static void rtl8192_SetWirelessMode(struct net_device *dev, u8 wireless_mode)
rtl8192_refresh_supportrate(priv);
}
-//init priv variables here. only non_zero value should be initialized here.
+/* init priv variables here. only non_zero value should be initialized here. */
static void rtl8192_init_priv_variable(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 i;
priv->card_8192 = NIC_8192U;
- priv->chan = 1; //set to channel 1
- priv->ieee80211->mode = WIRELESS_MODE_AUTO; //SET AUTO
+ priv->chan = 1; /*set to channel 1*/
+ priv->ieee80211->mode = WIRELESS_MODE_AUTO; /*SET AUTO*/
priv->ieee80211->iw_mode = IW_MODE_INFRA;
priv->ieee80211->ieee_up = 0;
priv->retry_rts = DEFAULT_RETRY_RTS;
priv->retry_data = DEFAULT_RETRY_DATA;
priv->ieee80211->rts = DEFAULT_RTS_THRESHOLD;
- priv->ieee80211->rate = 110; //11 mbps
+ priv->ieee80211->rate = 110; /*11 mbps*/
priv->ieee80211->short_slot = 1;
priv->promisc = (dev->flags & IFF_PROMISC) ? 1 : 0;
priv->CckPwEnl = 6;
- //for silent reset
+ /*for silent reset*/
priv->IrpPendingCount = 1;
priv->ResetProgress = RESET_TYPE_NORESET;
priv->bForcedSilentReset = 0;
priv->bDisableNormalResetCheck = false;
priv->force_reset = false;
-
- priv->ieee80211->FwRWRF = 0; //we don't use FW read/write RF until stable firmware is available.
+ /*we don't use FW read/write RF until stable firmware is available.*/
+ priv->ieee80211->FwRWRF = 0;
priv->ieee80211->current_network.beacon_interval = DEFAULT_BEACONINTERVAL;
priv->ieee80211->softmac_features = IEEE_SOFTMAC_SCAN |
IEEE_SOFTMAC_ASSOCIATE | IEEE_SOFTMAC_PROBERQ |
IEEE_SOFTMAC_PROBERS | IEEE_SOFTMAC_TX_QUEUE |
- IEEE_SOFTMAC_BEACONS;//added by amy 080604
+ IEEE_SOFTMAC_BEACONS;
priv->ieee80211->active_scan = 1;
priv->ieee80211->modulation = IEEE80211_CCK_MODULATION | IEEE80211_OFDM_MODULATION;
priv->ieee80211->host_encrypt = 1;
priv->ieee80211->host_decrypt = 1;
- priv->ieee80211->start_send_beacons = NULL; //-by amy 080604
- priv->ieee80211->stop_send_beacons = NULL; //-by amy 080604
+ priv->ieee80211->start_send_beacons = NULL;
+ priv->ieee80211->stop_send_beacons = NULL;
priv->ieee80211->softmac_hard_start_xmit = rtl8192_hard_start_xmit;
priv->ieee80211->set_chan = rtl8192_set_chan;
priv->ieee80211->link_change = rtl8192_link_change;
@@ -2486,15 +2504,12 @@ static void rtl8192_init_priv_variable(struct net_device *dev)
priv->ieee80211->tx_headroom = TX_PACKET_SHIFT_BYTES;
priv->ieee80211->qos_support = 1;
- //added by WB
priv->ieee80211->SetBWModeHandler = rtl8192_SetBWMode;
priv->ieee80211->handle_assoc_response = rtl8192_handle_assoc_response;
priv->ieee80211->handle_beacon = rtl8192_handle_beacon;
- //added by david
priv->ieee80211->GetNmodeSupportBySecCfg = GetNmodeSupportBySecCfg8192;
priv->ieee80211->GetHalfNmodeSupportByAPsHandler = GetHalfNmodeSupportByAPs819xUsb;
priv->ieee80211->SetWirelessMode = rtl8192_SetWirelessMode;
- //added by amy
priv->ieee80211->InitialGainHandler = InitialGain819xUsb;
priv->card_type = USB;
#ifdef TO_DO_LIST
@@ -2508,30 +2523,48 @@ static void rtl8192_init_priv_variable(struct net_device *dev)
priv->EarlyRxThreshold = 7;
priv->enable_gpio0 = 0;
priv->TransmitConfig =
- (TCR_MXDMA_2048<<TCR_MXDMA_OFFSET)| // Max DMA Burst Size per Tx DMA Burst, 7: reserved.
- (priv->ShortRetryLimit<<TCR_SRL_OFFSET)| // Short retry limit
- (priv->LongRetryLimit<<TCR_LRL_OFFSET) | // Long retry limit
- (false ? TCR_SAT : 0); // FALSE: HW provides PLCP length and LENGEXT, TRUE: SW provides them
+ /* Max DMA Burst Size per Tx DMA Burst, 7: reserved.*/
+ (TCR_MXDMA_2048<<TCR_MXDMA_OFFSET)|
+ /* Short retry limit */
+ (priv->ShortRetryLimit<<TCR_SRL_OFFSET)|
+ /* Long retry limit */
+ (priv->LongRetryLimit<<TCR_LRL_OFFSET) |
+ /* FALSE: HW provides PLCP length and LENGEXT,
+ * TRUE: SW provides them */
+ (false ? TCR_SAT : 0);
#ifdef TO_DO_LIST
if (Adapter->bInHctTest)
pHalData->ReceiveConfig = pHalData->CSMethod |
- RCR_AMF | RCR_ADF | //accept management/data
- //guangan200710
- RCR_ACF | //accept control frame for SW AP needs PS-poll, 2005.07.07, by rcnjko.
- RCR_AB | RCR_AM | RCR_APM | //accept BC/MC/UC
- RCR_AICV | RCR_ACRC32 | //accept ICV/CRC error packet
- ((u32)7<<RCR_MXDMA_OFFSET) | // Max DMA Burst Size per Rx DMA Burst, 7: unlimited.
- (pHalData->EarlyRxThreshold<<RCR_FIFO_OFFSET) | // Rx FIFO Threshold, 7: No Rx threshold.
+ /* accept management/data */
+ RCR_AMF | RCR_ADF |
+ /* accept control frame for
+ * SW AP needs PS-poll */
+ RCR_ACF |
+ /* accept BC/MC/UC */
+ RCR_AB | RCR_AM | RCR_APM |
+ /* accept ICV/CRC error packet*/
+ RCR_AICV | RCR_ACRC32 |
+ /* Max DMA Burst Size per
+ * Rx DMA Burst, 7: unlimited */
+ ((u32)7<<RCR_MXDMA_OFFSET) |
+ /* Rx FIFO Threshold,
+ * 7: No Rx threshold. */
+ (pHalData->EarlyRxThreshold<<RCR_FIFO_OFFSET) |
(pHalData->EarlyRxThreshold == 7 ? RCR_OnlyErlPkt : 0);
else
#endif
priv->ReceiveConfig =
- RCR_AMF | RCR_ADF | //accept management/data
- RCR_ACF | //accept control frame for SW AP needs PS-poll, 2005.07.07, by rcnjko.
- RCR_AB | RCR_AM | RCR_APM | //accept BC/MC/UC
- ((u32)7<<RCR_MXDMA_OFFSET)| // Max DMA Burst Size per Rx DMA Burst, 7: unlimited.
- (priv->EarlyRxThreshold<<RX_FIFO_THRESHOLD_SHIFT) | // Rx FIFO Threshold, 7: No Rx threshold.
+ /* accept management/data */
+ RCR_AMF | RCR_ADF |
+ /* accept control frame for SW AP needs PS-poll */
+ RCR_ACF |
+ /* accept BC/MC/UC */
+ RCR_AB | RCR_AM | RCR_APM |
+ /* Max DMA Burst Size per Rx DMA Burst, 7: unlimited. */
+ ((u32)7<<RCR_MXDMA_OFFSET)|
+ /* Rx FIFO Threshold, 7: No Rx threshold. */
+ (priv->EarlyRxThreshold<<RX_FIFO_THRESHOLD_SHIFT) |
(priv->EarlyRxThreshold == 7 ? RCR_ONLYERLPKT : 0);
priv->AcmControl = 0;
@@ -2551,11 +2584,11 @@ static void rtl8192_init_priv_variable(struct net_device *dev)
priv->rf_set_chan = rtl8192_phy_SwChnl;
}
-//init lock here
+/* init lock here */
static void rtl8192_init_priv_lock(struct r8192_priv *priv)
{
spin_lock_init(&priv->tx_lock);
- spin_lock_init(&priv->irq_lock);//added by thomas
+ spin_lock_init(&priv->irq_lock);
sema_init(&priv->wx_sem, 1);
sema_init(&priv->rf_sem, 1);
mutex_init(&priv->mutex);
@@ -2564,7 +2597,7 @@ static void rtl8192_init_priv_lock(struct r8192_priv *priv)
extern void rtl819x_watchdog_wqcallback(struct work_struct *work);
void rtl8192_irq_rx_tasklet(struct r8192_priv *priv);
-//init tasklet and wait_queue here. only 2.6 above kernel is considered
+/* init tasklet and wait_queue here. */
#define DRV_NAME "wlan0"
static void rtl8192_init_priv_task(struct net_device *dev)
{
@@ -2593,12 +2626,11 @@ static void rtl8192_get_eeprom_size(struct net_device *dev)
RT_TRACE(COMP_EPROM, "===========>%s()\n", __func__);
read_nic_word_E(dev, EPROM_CMD, &curCR);
RT_TRACE(COMP_EPROM, "read from Reg EPROM_CMD(%x):%x\n", EPROM_CMD, curCR);
- //whether need I consider BIT5?
+ /* whether need I consider BIT5? */
priv->epromtype = (curCR & Cmd9346CR_9356SEL) ? EPROM_93c56 : EPROM_93c46;
RT_TRACE(COMP_EPROM, "<===========%s(), epromtype:%d\n", __func__, priv->epromtype);
}
-//used to swap endian. as ntohl & htonl are not necessary to swap endian, so use this instead.
static inline u16 endian_swap(u16 *data)
{
u16 tmp = *data;
@@ -2614,7 +2646,7 @@ static void rtl8192_read_eeprom_info(struct net_device *dev)
u16 tmpValue = 0;
int i;
RT_TRACE(COMP_EPROM, "===========>%s()\n", __func__);
- wEPROM_ID = eprom_read(dev, 0); //first read EEPROM ID out;
+ wEPROM_ID = eprom_read(dev, 0); /* first read EEPROM ID out; */
RT_TRACE(COMP_EPROM, "EEPROM ID is 0x%x\n", wEPROM_ID);
if (wEPROM_ID != RTL8190_EEPROM_ID) {
@@ -2639,7 +2671,7 @@ static void rtl8192_read_eeprom_info(struct net_device *dev)
priv->eeprom_CustomerID = 0;
}
RT_TRACE(COMP_EPROM, "vid:0x%4x, pid:0x%4x, CustomID:0x%2x, ChanPlan:0x%x\n", priv->eeprom_vid, priv->eeprom_pid, priv->eeprom_CustomerID, priv->eeprom_ChannelPlan);
- //set channelplan from eeprom
+ /* set channelplan from eeprom */
priv->ChannelPlan = priv->eeprom_ChannelPlan;
if (bLoad_From_EEPOM) {
int i;
@@ -2650,40 +2682,40 @@ static void rtl8192_read_eeprom_info(struct net_device *dev)
}
} else {
memcpy(dev->dev_addr, bMac_Tmp_Addr, 6);
- //should I set IDR0 here?
+ /* should I set IDR0 here? */
}
RT_TRACE(COMP_EPROM, "MAC addr:%pM\n", dev->dev_addr);
- priv->rf_type = RTL819X_DEFAULT_RF_TYPE; //default 1T2R
+ priv->rf_type = RTL819X_DEFAULT_RF_TYPE; /* default 1T2R */
priv->rf_chip = RF_8256;
if (priv->card_8192_version == (u8)VERSION_819xU_A) {
- //read Tx power gain offset of legacy OFDM to HT rate
+ /* read Tx power gain offset of legacy OFDM to HT rate */
if (bLoad_From_EEPOM)
priv->EEPROMTxPowerDiff = (eprom_read(dev, (EEPROM_TxPowerDiff>>1))&0xff00) >> 8;
else
priv->EEPROMTxPowerDiff = EEPROM_Default_TxPower;
RT_TRACE(COMP_EPROM, "TxPowerDiff:%d\n", priv->EEPROMTxPowerDiff);
- //read ThermalMeter from EEPROM
+ /* read ThermalMeter from EEPROM */
if (bLoad_From_EEPOM)
priv->EEPROMThermalMeter = (u8)(eprom_read(dev, (EEPROM_ThermalMeter>>1))&0x00ff);
else
priv->EEPROMThermalMeter = EEPROM_Default_ThermalMeter;
RT_TRACE(COMP_EPROM, "ThermalMeter:%d\n", priv->EEPROMThermalMeter);
- //vivi, for tx power track
+ /* for tx power track */
priv->TSSI_13dBm = priv->EEPROMThermalMeter *100;
- //read antenna tx power offset of B/C/D to A from EEPROM
+ /* read antenna tx power offset of B/C/D to A from EEPROM */
if (bLoad_From_EEPOM)
priv->EEPROMPwDiff = (eprom_read(dev, (EEPROM_PwDiff>>1))&0x0f00)>>8;
else
priv->EEPROMPwDiff = EEPROM_Default_PwDiff;
RT_TRACE(COMP_EPROM, "TxPwDiff:%d\n", priv->EEPROMPwDiff);
- // Read CrystalCap from EEPROM
+ /* Read CrystalCap from EEPROM */
if (bLoad_From_EEPOM)
priv->EEPROMCrystalCap = (eprom_read(dev, (EEPROM_CrystalCap>>1))&0x0f);
else
priv->EEPROMCrystalCap = EEPROM_Default_CrystalCap;
RT_TRACE(COMP_EPROM, "CrystalCap = %d\n", priv->EEPROMCrystalCap);
- //get per-channel Tx power level
+ /* get per-channel Tx power level */
if (bLoad_From_EEPOM)
priv->EEPROM_Def_Ver = (eprom_read(dev, (EEPROM_TxPwIndex_Ver>>1))&0xff00)>>8;
else
@@ -2733,10 +2765,9 @@ static void rtl8192_read_eeprom_info(struct net_device *dev)
else
tmpValue = 0x10;
priv->EEPROMTxPowerLevelOFDM24G[2] = (u8)tmpValue;
- }//endif EEPROM_Def_Ver == 1
+ } /* endif EEPROM_Def_Ver == 1 */
- //update HAL variables
- //
+ /* update HAL variables */
for (i = 0; i < 14; i++) {
if (i <= 3)
priv->TxPowerLevelOFDM24G[i] = priv->EEPROMTxPowerLevelOFDM24G[0];
@@ -2764,18 +2795,18 @@ static void rtl8192_read_eeprom_info(struct net_device *dev)
}
}
priv->TxPowerDiff = priv->EEPROMPwDiff;
- // Antenna B gain offset to antenna A, bit0~3
+ /* Antenna B gain offset to antenna A, bit0~3 */
priv->AntennaTxPwDiff[0] = (priv->EEPROMTxPowerDiff & 0xf);
- // Antenna C gain offset to antenna A, bit4~7
+ /* Antenna C gain offset to antenna A, bit4~7 */
priv->AntennaTxPwDiff[1] = ((priv->EEPROMTxPowerDiff & 0xf0)>>4);
- // CrystalCap, bit12~15
+ /* CrystalCap, bit12~15 */
priv->CrystalCap = priv->EEPROMCrystalCap;
- // ThermalMeter, bit0~3 for RFIC1, bit4~7 for RFIC2
- // 92U does not enable TX power tracking.
+ /* ThermalMeter, bit0~3 for RFIC1, bit4~7 for RFIC2 */
+ /* 92U does not enable TX power tracking. */
priv->ThermalMeter[0] = priv->EEPROMThermalMeter;
- }//end if VersionID == VERSION_819xU_A
+ } /* end if VersionID == VERSION_819xU_A */
- //added by vivi, for dlink led, 20080416
+ /* for dlink led */
switch (priv->eeprom_CustomerID) {
case EEPROM_CID_RUNTOP:
priv->CustomerID = RT_CID_819x_RUNTOP;
@@ -2813,10 +2844,10 @@ static void rtl8192_read_eeprom_info(struct net_device *dev)
RT_TRACE(COMP_EPROM, "\n2T4R config\n");
}
- // 2008/01/16 MH We can only know RF type in the function. So we have to init
- // DIG RATR table again.
+ /* We can only know RF type in the function. So we have to init
+ * DIG RATR table again. */
init_rate_adaptive(dev);
- //we need init DIG RATR table here again.
+ /* we need init DIG RATR table here again. */
RT_TRACE(COMP_EPROM, "<===========%s()\n", __func__);
return;
@@ -2890,8 +2921,7 @@ static void rtl8192_hwconfig(struct net_device *dev)
struct r8192_priv *priv = ieee80211_priv(dev);
u32 ratr_value = 0;
- // Set RRSR, RATR, and BW_OPMODE registers
- //
+ /* Set RRSR, RATR, and BW_OPMODE registers */
switch (priv->ieee80211->mode) {
case WIRELESS_MODE_B:
regBwOpMode = BW_OPMODE_20MHZ;
@@ -2924,8 +2954,9 @@ static void rtl8192_hwconfig(struct net_device *dev)
}
break;
case WIRELESS_MODE_N_24G:
- // It support CCK rate by default.
- // CCK rate will be filtered out only when associated AP does not support it.
+ /* It support CCK rate by default.
+ * CCK rate will be filtered out only when associated AP does
+ * not support it. */
regBwOpMode = BW_OPMODE_20MHZ;
regRATR = RATE_ALL_CCK | RATE_ALL_OFDM_AG | RATE_ALL_OFDM_1SS | RATE_ALL_OFDM_2SS;
regRRSR = RATE_ALL_CCK | RATE_ALL_OFDM_AG;
@@ -2947,25 +2978,23 @@ static void rtl8192_hwconfig(struct net_device *dev)
regRRSR = ((regTmp) << 24) | (regRRSR & 0x00ffffff);
write_nic_dword(dev, RRSR, regRRSR);
- //
- // Set Retry Limit here
- //
+ /* Set Retry Limit here */
write_nic_word(dev, RETRY_LIMIT,
priv->ShortRetryLimit << RETRY_LIMIT_SHORT_SHIFT |
priv->LongRetryLimit << RETRY_LIMIT_LONG_SHIFT);
- // Set Contention Window here
+ /* Set Contention Window here */
- // Set Tx AGC
+ /* Set Tx AGC */
- // Set Tx Antenna including Feedback control
+ /* Set Tx Antenna including Feedback control */
- // Set Auto Rate fallback control
+ /* Set Auto Rate fallback control */
}
-//InitializeAdapter and PhyCfg
+/* InitializeAdapter and PhyCfg */
static bool rtl8192_adapter_start(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
@@ -2975,7 +3004,7 @@ static bool rtl8192_adapter_start(struct net_device *dev)
u8 tmp;
RT_TRACE(COMP_INIT, "====>%s()\n", __func__);
priv->Rf_Mode = RF_OP_By_SW_3wire;
- //for ASIC power on sequence
+ /* for ASIC power on sequence */
write_nic_byte_E(dev, 0x5f, 0x80);
mdelay(50);
write_nic_byte_E(dev, 0x5f, 0xf0);
@@ -2984,21 +3013,21 @@ static bool rtl8192_adapter_start(struct net_device *dev)
write_nic_byte(dev, 0x17, 0x37);
mdelay(10);
priv->pFirmware->firmware_status = FW_STATUS_0_INIT;
- //config CPUReset Register
- //Firmware Reset or not?
+ /* config CPUReset Register */
+ /* Firmware Reset or not? */
read_nic_dword(dev, CPU_GEN, &dwRegRead);
if (priv->pFirmware->firmware_status == FW_STATUS_0_INIT)
- dwRegRead |= CPU_GEN_SYSTEM_RESET; //do nothing here?
+ dwRegRead |= CPU_GEN_SYSTEM_RESET; /* do nothing here? */
else if (priv->pFirmware->firmware_status == FW_STATUS_5_READY)
dwRegRead |= CPU_GEN_FIRMWARE_RESET;
else
RT_TRACE(COMP_ERR, "ERROR in %s(): undefined firmware state(%d)\n", __func__, priv->pFirmware->firmware_status);
write_nic_dword(dev, CPU_GEN, dwRegRead);
- //config BB.
+ /* config BB. */
rtl8192_BBConfig(dev);
- //Loopback mode or not
+ /* Loopback mode or not */
priv->LoopbackMode = RTL819xU_NO_LOOPBACK;
read_nic_dword(dev, CPU_GEN, &dwRegRead);
@@ -3011,27 +3040,27 @@ static bool rtl8192_adapter_start(struct net_device *dev)
write_nic_dword(dev, CPU_GEN, dwRegRead);
- //after reset cpu, we need wait for a seconds to write in register.
+ /* after reset cpu, we need wait for a seconds to write in register. */
udelay(500);
- //xiong add for new bitfile:usb suspend reset pin set to 1. //do we need?
+ /* add for new bitfile:usb suspend reset pin set to 1. do we need? */
read_nic_byte_E(dev, 0x5f, &tmp);
write_nic_byte_E(dev, 0x5f, tmp|0x20);
- //Set Hardware
+ /* Set Hardware */
rtl8192_hwconfig(dev);
- //turn on Tx/Rx
+ /* turn on Tx/Rx */
write_nic_byte(dev, CMDR, CR_RE|CR_TE);
- //set IDR0 here
+ /* set IDR0 here */
write_nic_dword(dev, MAC0, ((u32 *)dev->dev_addr)[0]);
write_nic_word(dev, MAC4, ((u16 *)(dev->dev_addr + 4))[0]);
- //set RCR
+ /* set RCR */
write_nic_dword(dev, RCR, priv->ReceiveConfig);
- //Initialize Number of Reserved Pages in Firmware Queue
+ /* Initialize Number of Reserved Pages in Firmware Queue */
write_nic_dword(dev, RQPN1, NUM_OF_PAGE_IN_FW_QUEUE_BK << RSVD_FW_QUEUE_PAGE_BK_SHIFT |
NUM_OF_PAGE_IN_FW_QUEUE_BE << RSVD_FW_QUEUE_PAGE_BE_SHIFT |
NUM_OF_PAGE_IN_FW_QUEUE_VI << RSVD_FW_QUEUE_PAGE_VI_SHIFT |
@@ -3042,8 +3071,8 @@ static bool rtl8192_adapter_start(struct net_device *dev)
NUM_OF_PAGE_IN_FW_QUEUE_BCN<<RSVD_FW_QUEUE_PAGE_BCN_SHIFT);
write_nic_dword(dev, RATR0+4*7, (RATE_ALL_OFDM_AG | RATE_ALL_CCK));
- //Set AckTimeout
- // TODO: (it value is only for FPGA version). need to be changed!!2006.12.18, by Emily
+ /* Set AckTimeout */
+ /* TODO: (it value is only for FPGA version). need to be changed!!*/
write_nic_byte(dev, ACK_TIMEOUT, 0x30);
if (priv->ResetProgress == RESET_TYPE_NORESET)
@@ -3056,7 +3085,7 @@ static bool rtl8192_adapter_start(struct net_device *dev)
write_nic_byte(dev, SECR, SECR_value);
}
- //Beacon related
+ /* Beacon related */
write_nic_word(dev, ATIMWND, 2);
write_nic_word(dev, BCN_INTERVAL, 100);
@@ -3067,7 +3096,7 @@ static bool rtl8192_adapter_start(struct net_device *dev)
write_nic_dword(dev, WDCAPARA_ADD[i], DEFAULT_EDCA);
}
#ifdef USB_RX_AGGREGATION_SUPPORT
- //3 For usb rx firmware aggregation control
+ /* 3 For usb rx firmware aggregation control */
if (priv->ResetProgress == RESET_TYPE_NORESET) {
u32 ulValue;
PRT_HIGH_THROUGHPUT pHTInfo = priv->ieee80211->pHTInfo;
@@ -3090,7 +3119,7 @@ static bool rtl8192_adapter_start(struct net_device *dev)
rtl8192_phy_setTxPower(dev, priv->chan);
}
- //Firmware download
+ /* Firmware download */
init_status = init_firmware(dev);
if (!init_status) {
RT_TRACE(COMP_ERR, "ERR!!! %s(): Firmware download is failed\n", __func__);
@@ -3103,10 +3132,12 @@ static bool rtl8192_adapter_start(struct net_device *dev)
if (pMgntInfo->RegRfOff == TRUE) { /* User disable RF via registry. */
RT_TRACE((COMP_INIT|COMP_RF), DBG_LOUD, ("InitializeAdapter819xUsb(): Turn off RF for RegRfOff ----------\n"));
MgntActSet_RF_State(Adapter, eRfOff, RF_CHANGE_BY_SW);
- // Those actions will be discard in MgntActSet_RF_State because of the same state
+ /* Those actions will be discard in MgntActSet_RF_State
+ * because of the same state */
for (eRFPath = 0; eRFPath < pHalData->NumTotalRFPath; eRFPath++)
PHY_SetRFReg(Adapter, (RF90_RADIO_PATH_E)eRFPath, 0x4, 0xC00, 0x0);
- } else if (pMgntInfo->RfOffReason > RF_CHANGE_BY_PS) { /* H/W or S/W RF OFF before sleep. */
+ /* H/W or S/W RF OFF before sleep. */
+ } else if (pMgntInfo->RfOffReason > RF_CHANGE_BY_PS) {
RT_TRACE((COMP_INIT|COMP_RF), DBG_LOUD, ("InitializeAdapter819xUsb(): Turn off RF for RfOffReason(%d) ----------\n", pMgntInfo->RfOffReason));
MgntActSet_RF_State(Adapter, eRfOff, pMgntInfo->RfOffReason);
} else {
@@ -3123,7 +3154,7 @@ static bool rtl8192_adapter_start(struct net_device *dev)
}
}
#endif
- //config RF.
+ /* config RF. */
if (priv->ResetProgress == RESET_TYPE_NORESET) {
rtl8192_phy_RFConfig(dev);
RT_TRACE(COMP_INIT, "%s():after phy RF config\n", __func__);
@@ -3131,7 +3162,7 @@ static bool rtl8192_adapter_start(struct net_device *dev)
if (priv->ieee80211->FwRWRF)
- // We can force firmware to do RF-R/W
+ /* We can force firmware to do RF-R/W */
priv->Rf_Mode = RF_OP_By_FW;
else
priv->Rf_Mode = RF_OP_By_SW_3wire;
@@ -3143,7 +3174,7 @@ static bool rtl8192_adapter_start(struct net_device *dev)
rtl8192_setBBreg(dev, rFPGA0_RFMOD, bOFDMEn, 0x1);
if (priv->ResetProgress == RESET_TYPE_NORESET) {
- //if D or C cut
+ /* if D or C cut */
u8 tmpvalue;
read_nic_byte(dev, 0x301, &tmpvalue);
if (tmpvalue == 0x03) {
@@ -3228,9 +3259,7 @@ static RESET_TYPE TxCheckStuck(struct net_device *dev)
u8 QueueID;
bool bCheckFwTxCnt = false;
- //
- // Decide such threshold according to current power save mode
- //
+ /* Decide such threshold according to current power save mode */
for (QueueID = 0; QueueID <= BEACON_QUEUE; QueueID++) {
if (QueueID == TXCMD_QUEUE)
@@ -3261,8 +3290,8 @@ static bool HalRxCheckStuck819xUsb(struct net_device *dev)
static u8 rx_chk_cnt;
read_nic_word(dev, 0x130, &RegRxCounter);
RT_TRACE(COMP_RESET, "%s(): RegRxCounter is %d,RxCounter is %d\n", __func__, RegRxCounter, priv->RxCounter);
- // If rssi is small, we should check rx for long time because of bad rx.
- // or maybe it will continuous silent reset every 2 seconds.
+ /* If rssi is small, we should check rx for long time because of bad rx.
+ * or maybe it will continuous silent reset every 2 seconds. */
rx_chk_cnt++;
if (priv->undecorated_smoothed_pwdb >= (RateAdaptiveTH_High+5)) {
rx_chk_cnt = 0; //high rssi, check rx stuck right now.
@@ -3337,14 +3366,17 @@ static RESET_TYPE rtl819x_ifcheck_resetornot(struct net_device *dev)
TxResetType = TxCheckStuck(dev);
if (rfState != eRfOff ||
(priv->ieee80211->iw_mode != IW_MODE_ADHOC)) {
- // If driver is in the status of firmware download failure , driver skips RF initialization and RF is
- // in turned off state. Driver should check whether Rx stuck and do silent reset. And
- // if driver is in firmware download failure status, driver should initialize RF in the following
- // silent reset procedure Emily, 2008.01.21
-
- // Driver should not check RX stuck in IBSS mode because it is required to
- // set Check BSSID in order to send beacon, however, if check BSSID is
- // set, STA cannot hear any packet at all. Emily, 2008.04.12
+ /* If driver is in the status of firmware download failure,
+ * driver skips RF initialization and RF is in turned off state.
+ * Driver should check whether Rx stuck and do silent reset.
+ * And if driver is in firmware download failure status, driver
+ * should initialize RF in the following silent reset procedure
+ */
+
+ /* Driver should not check RX stuck in IBSS mode because it is
+ * required to set Check BSSID in order to send beacon, however,
+ * if check BSSID is set, STA cannot hear any packet at all.
+ */
RxResetType = RxCheckStuck(dev);
}
if (TxResetType == RESET_TYPE_NORMAL || RxResetType == RESET_TYPE_NORMAL) {
@@ -3434,12 +3466,12 @@ static void CamRestoreAllEntry(struct net_device *dev)
CAM_CONST_ADDR[0], 0, NULL);
}
}
-//////////////////////////////////////////////////////////////
-// This function is used to fix Tx/Rx stop bug temporarily.
-// This function will do "system reset" to NIC when Tx or Rx is stuck.
-// The method checking Tx/Rx stuck of this function is supported by FW,
-// which reports Tx and Rx counter to register 0x128 and 0x130.
-//////////////////////////////////////////////////////////////
+/*------------------------------------------------------------------------------
+ * This function is used to fix Tx/Rx stop bug temporarily.
+ * This function will do "system reset" to NIC when Tx or Rx is stuck.
+ * The method checking Tx/Rx stuck of this function is supported by FW,
+ * which reports Tx and Rx counter to register 0x128 and 0x130.
+ *----------------------------------------------------------------------------*/
static void rtl819x_ifsilentreset(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
@@ -3448,15 +3480,17 @@ static void rtl819x_ifsilentreset(struct net_device *dev)
struct ieee80211_device *ieee = priv->ieee80211;
- // 2007.07.20. If we need to check CCK stop, please uncomment this line.
- //bStuck = Adapter->HalFunc.CheckHWStopHandler(Adapter);
+ /* If we need to check CCK stop, please uncomment this line. */
+ /*
+ bStuck = Adapter->HalFunc.CheckHWStopHandler(Adapter);
+ */
if (priv->ResetProgress == RESET_TYPE_NORESET) {
RESET_START:
RT_TRACE(COMP_RESET, "=========>Reset progress!! \n");
- // Set the variable for reset.
+ /* Set the variable for reset. */
priv->ResetProgress = RESET_TYPE_SILENT;
down(&priv->wx_sem);
if (priv->up == 0) {
@@ -3526,7 +3560,7 @@ RESET_START:
priv->bForcedSilentReset = false;
priv->bResetInProgress = false;
- // For test --> force write UFWP.
+ /* For test --> force write UFWP. */
write_nic_byte(dev, UFWP, 1);
RT_TRACE(COMP_RESET, "Reset finished!! ====>[%d]\n", priv->reset_count);
}
@@ -3540,11 +3574,11 @@ void CAM_read_entry(struct net_device *dev, u32 iIndex)
u32 ulStatus;
s32 i = 100;
for (entry_i = 0; entry_i < CAM_CONTENT_COUNT; entry_i++) {
- // polling bit, and No Write enable, and address
+ /* polling bit, and No Write enable, and address */
target_command = entry_i+CAM_CONTENT_COUNT*iIndex;
target_command = target_command | BIT31;
- //Check polling bit is clear
+ /* Check polling bit is clear */
while ((i--) >= 0) {
read_nic_dword(dev, RWCAM, &ulStatus);
if (ulStatus & BIT31)
@@ -3595,7 +3629,7 @@ void rtl819x_watchdog_wqcallback(struct work_struct *work)
return;
hal_dm_watchdog(dev);
- //to get busy traffic condition
+ /* to get busy traffic condition */
if (ieee->state == IEEE80211_LINKED) {
if (ieee->LinkDetectInfo.NumRxOkInPeriod > 666 ||
ieee->LinkDetectInfo.NumTxOkInPeriod > 666 ) {
@@ -3605,7 +3639,7 @@ void rtl819x_watchdog_wqcallback(struct work_struct *work)
ieee->LinkDetectInfo.NumTxOkInPeriod = 0;
ieee->LinkDetectInfo.bBusyTraffic = bBusyTraffic;
}
- //added by amy for AP roaming
+ /* added by amy for AP roaming */
if (priv->ieee80211->state == IEEE80211_LINKED && priv->ieee80211->iw_mode == IW_MODE_INFRA) {
rtl819x_update_rxcounts(priv, &TotalRxBcnNum, &TotalRxDataNum);
@@ -3625,7 +3659,7 @@ void rtl819x_watchdog_wqcallback(struct work_struct *work)
}
priv->ieee80211->LinkDetectInfo.NumRecvBcnInPeriod = 0;
priv->ieee80211->LinkDetectInfo.NumRecvDataInPeriod = 0;
- //check if reset the driver
+ /* check if reset the driver */
if (check_reset_cnt++ >= 3) {
ResetType = rtl819x_ifcheck_resetornot(dev);
check_reset_cnt = 3;
@@ -3741,7 +3775,9 @@ int rtl8192_down(struct net_device *dev)
for (i = 0; i < MAX_QUEUE_SIZE; i++)
skb_queue_purge(&priv->ieee80211->skb_drv_aggQ[i]);
- //as cancel_delayed_work will del work->timer, so if work is not defined as struct delayed_work, it will corrupt
+ /* as cancel_delayed_work will del work->timer, so if work is not
+ * defined as struct delayed_work, it will corrupt
+ */
rtl8192_cancel_deferred_work(priv);
deinit_hal_dm(dev);
del_timer_sync(&priv->watch_dog_timer);
@@ -3843,7 +3879,7 @@ static int rtl8192_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
switch (cmd) {
case RTL_IOCTL_WPA_SUPPLICANT:
- //parse here for HW security
+ /* parse here for HW security */
if (ipw->cmd == IEEE_CMD_SET_ENCRYPTION) {
if (ipw->u.crypt.set_tx) {
if (strcmp(ipw->u.crypt.alg, "CCMP") == 0) {
@@ -3862,8 +3898,12 @@ static int rtl8192_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
if (ieee->pairwise_key_type) {
memcpy((u8 *)key, ipw->u.crypt.key, 16);
EnableHWSecurityConfig8192(dev);
- //we fill both index entry and 4th entry for pairwise key as in IPW interface, adhoc will only get here, so we need index entry for its default key serching!
- //added by WB.
+ /* we fill both index entry and 4th
+ * entry for pairwise key as in IPW
+ * interface, adhoc will only get here,
+ * so we need index entry for its
+ * default key serching!
+ */
setKey(dev, 4, ipw->u.crypt.idx, ieee->pairwise_key_type, (u8 *)ieee->ap_mac_addr, 0, key);
if (ieee->auth_mode != 2)
setKey(dev, ipw->u.crypt.idx, ipw->u.crypt.idx, ieee->pairwise_key_type, (u8 *)ieee->ap_mac_addr, 0, key);
@@ -3885,11 +3925,16 @@ static int rtl8192_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
if (ieee->group_key_type) {
setKey(dev, ipw->u.crypt.idx,
- ipw->u.crypt.idx, //KeyIndex
- ieee->group_key_type, //KeyType
- broadcast_addr, //MacAddr
- 0, //DefaultKey
- key); //KeyContent
+ /* KeyIndex */
+ ipw->u.crypt.idx,
+ /* KeyType */
+ ieee->group_key_type,
+ /* MacAddr */
+ broadcast_addr,
+ /* DefaultKey */
+ 0,
+ /* KeyContent */
+ key);
}
}
}
@@ -4049,13 +4094,11 @@ static void UpdateRxPktTimeStamp8190(struct net_device *dev,
}
}
-//by amy 080606
-
-static long rtl819x_translate_todbm(u8 signal_strength_index)// 0-100 index.
+static long rtl819x_translate_todbm(u8 signal_strength_index)/* 0-100 index. */
{
- long signal_power; // in dBm.
+ long signal_power; /* in dBm. */
- // Translate to dBm (x=0.5y-95).
+ /* Translate to dBm (x=0.5y-95). */
signal_power = (long)((signal_strength_index + 1) >> 1);
signal_power -= 95;
@@ -4088,13 +4131,13 @@ static void rtl8192_process_phyinfo(struct r8192_priv *priv, u8 *buffer,
sc = le16_to_cpu(hdr->seq_ctl);
frag = WLAN_GET_SEQ_FRAG(sc);
seq = WLAN_GET_SEQ_SEQ(sc);
- //cosa add 04292008 to record the sequence number
+ /* to record the sequence number */
pcurrent_stats->Seq_Num = seq;
- //
- // Check whether we should take the previous packet into accounting
- //
+ /*
+ * Check whether we should take the previous packet into accounting
+ */
if (!pprevious_stats->bIsAMPDU) {
- // if previous packet is not aggregated packet
+ /* if previous packet is not aggregated packet */
bcheck = true;
}
@@ -4109,13 +4152,13 @@ static void rtl8192_process_phyinfo(struct r8192_priv *priv, u8 *buffer,
if (slide_rssi_index >= PHY_RSSI_SLID_WIN_MAX)
slide_rssi_index = 0;
- // <1> Showed on UI for user, in dbm
+ /* <1> Showed on UI for user, in dbm */
tmp_val = priv->stats.slide_rssi_total/slide_rssi_statistics;
priv->stats.signal_strength = rtl819x_translate_todbm((u8)tmp_val);
pcurrent_stats->rssi = priv->stats.signal_strength;
- //
- // If the previous packet does not match the criteria, neglect it
- //
+ /*
+ * If the previous packet does not match the criteria, neglect it
+ */
if (!pprevious_stats->bPacketMatchBSSID) {
if (!pprevious_stats->bToSelfBA)
return;
@@ -4124,25 +4167,26 @@ static void rtl8192_process_phyinfo(struct r8192_priv *priv, u8 *buffer,
if (!bcheck)
return;
+ /* only rtl8190 supported */
+ /*
+ rtl8190_process_cck_rxpathsel(priv,pprevious_stats);
+ */
- //rtl8190_process_cck_rxpathsel(priv,pprevious_stats);//only rtl8190 supported
-
- //
- // Check RSSI
- //
+ /*
+ * Check RSSI
+ */
priv->stats.num_process_phyinfo++;
/* record the general signal strength to the sliding window. */
- // <2> Showed on UI for engineering
- // hardware does not provide rssi information for each rf path in CCK
+ /* <2> Showed on UI for engineering
+ * hardware does not provide rssi information for each rf path in CCK */
if (!pprevious_stats->bIsCCK && (pprevious_stats->bPacketToSelf || pprevious_stats->bToSelfBA)) {
for (rfpath = RF90_PATH_A; rfpath < priv->NumTotalRFPath; rfpath++) {
if (!rtl8192_phy_CheckIsLegalRFPath(priv->ieee80211->dev, rfpath))
continue;
- //Fixed by Jacken 2008-03-20
if (priv->stats.rx_rssi_percentage[rfpath] == 0)
priv->stats.rx_rssi_percentage[rfpath] = pprevious_stats->RxMIMOSignalStrength[rfpath];
if (pprevious_stats->RxMIMOSignalStrength[rfpath] > priv->stats.rx_rssi_percentage[rfpath]) {
@@ -4160,9 +4204,9 @@ static void rtl8192_process_phyinfo(struct r8192_priv *priv, u8 *buffer,
}
- //
- // Check PWDB.
- //
+ /*
+ * Check PWDB.
+ */
RT_TRACE(COMP_RXDESC, "Smooth %s PWDB = %d\n",
pprevious_stats->bIsCCK ? "CCK" : "OFDM",
pprevious_stats->RxPWDBAll);
@@ -4205,9 +4249,9 @@ static void rtl8192_process_phyinfo(struct r8192_priv *priv, u8 *buffer,
}
- //
- // Check EVM
- //
+ /*
+ * Check EVM
+ */
/* record the general EVM to the sliding window. */
if (pprevious_stats->SignalQuality) {
if (pprevious_stats->bPacketToSelf || pprevious_stats->bPacketBeacon || pprevious_stats->bToSelfBA) {
@@ -4223,14 +4267,15 @@ static void rtl8192_process_phyinfo(struct r8192_priv *priv, u8 *buffer,
if (slide_evm_index >= PHY_RSSI_SLID_WIN_MAX)
slide_evm_index = 0;
- // <1> Showed on UI for user, in percentage.
+ /* <1> Showed on UI for user, in percentage. */
tmp_val = priv->stats.slide_evm_total/slide_evm_statistics;
priv->stats.signal_quality = tmp_val;
- //cosa add 10/11/2007, Showed on UI for user in Windows Vista, for Link quality.
+ /* Showed on UI for user in Windows Vista,
+ * for Link quality. */
priv->stats.last_signal_strength_inpercent = tmp_val;
}
- // <2> Showed on UI for engineering
+ /* <2> Showed on UI for engineering */
if (pprevious_stats->bPacketToSelf || pprevious_stats->bPacketBeacon || pprevious_stats->bToSelfBA) {
for (nspatial_stream = 0; nspatial_stream < 2; nspatial_stream++) { /* 2 spatial stream */
if (pprevious_stats->RxMIMOSignalQuality[nspatial_stream] != -1) {
@@ -4290,16 +4335,15 @@ static u8 rtl819x_evm_dbtopercentage(char value)
ret_val = 100;
return ret_val;
}
-//
-// Description:
-// We want good-looking for signal strength/quality
-// 2007/7/19 01:09, by cosa.
-//
+/*
+ * Description:
+ * We want good-looking for signal strength/quality
+ */
static long rtl819x_signal_scale_mapping(long currsig)
{
long retsig;
- // Step 1. Scale mapping.
+ /* Step 1. Scale mapping. */
if (currsig >= 61 && currsig <= 100)
retsig = 90 + ((currsig - 60) / 4);
else if (currsig >= 41 && currsig <= 60)
@@ -4367,7 +4411,7 @@ static void rtl8192_query_rxphystatus(struct r8192_priv *priv,
is_cck_rate = rx_hal_is_cck_rate(pdrvinfo);
- // Record it for next packet processing
+ /* Record it for next packet processing */
memset(precord_stats, 0, sizeof(struct ieee80211_rx_stats));
pstats->bPacketMatchBSSID = precord_stats->bPacketMatchBSSID = bpacket_match_bssid;
pstats->bPacketToSelf = precord_stats->bPacketToSelf = bpacket_toself;
@@ -4390,13 +4434,13 @@ static void rtl8192_query_rxphystatus(struct r8192_priv *priv,
precord_stats->RxMIMOSignalQuality[1] = -1;
if (is_cck_rate) {
- //
- // (1)Hardware does not provide RSSI for CCK
- //
+ /*
+ * (1)Hardware does not provide RSSI for CCK
+ */
- //
- // (2)PWDB, Average PWDB cacluated by hardware (for rate adaptive)
- //
+ /*
+ * (2)PWDB, Average PWDB cacluated by hardware (for rate adaptive)
+ */
u8 report;
priv->stats.numqry_phystatusCCK++;
@@ -4405,9 +4449,8 @@ static void rtl8192_query_rxphystatus(struct r8192_priv *priv,
report = pcck_buf->cck_agc_rpt & 0xc0;
report = report>>6;
switch (report) {
- //Fixed by Jacken from Bryant 2008-03-20
- //Original value is -38 , -26 , -14 , -2
- //Fixed value is -35 , -23 , -11 , 6
+ /* Original value is -38 , -26 , -14 , -2*/
+ /* Fixed value is -35 , -23 , -11 , 6 */
case 0x3:
rx_pwr_all = -35 - (pcck_buf->cck_agc_rpt & 0x3e);
break;
@@ -4444,9 +4487,9 @@ static void rtl8192_query_rxphystatus(struct r8192_priv *priv,
pstats->RxPWDBAll = precord_stats->RxPWDBAll = pwdb_all;
pstats->RecvSignalPower = pwdb_all;
- //
- // (3) Get Signal Quality (EVM)
- //
+ /*
+ * (3) Get Signal Quality (EVM)
+ */
if (pstats->RxPWDBAll > 40) {
sq = 100;
@@ -4466,11 +4509,11 @@ static void rtl8192_query_rxphystatus(struct r8192_priv *priv,
} else {
priv->stats.numqry_phystatusHT++;
- //
- // (1)Get RSSI for HT rate
- //
+ /*
+ * (1)Get RSSI for HT rate
+ */
for (i = RF90_PATH_A; i < priv->NumTotalRFPath; i++) {
- // 2008/01/30 MH we will judge RF RX path now.
+ /* we will judge RF RX path now. */
if (priv->brfpath_rxenable[i])
rf_rx_num++;
else
@@ -4479,11 +4522,10 @@ static void rtl8192_query_rxphystatus(struct r8192_priv *priv,
if (!rtl8192_phy_CheckIsLegalRFPath(priv->ieee80211->dev, i))
continue;
- //Fixed by Jacken from Bryant 2008-03-20
- //Original value is 106
+ /* Original value is 106 */
rx_pwr[i] = ((pofdm_buf->trsw_gain_X[i]&0x3F)*2) - 106;
- //Get Rx snr value in DB
+ /* Get Rx snr value in DB */
tmp_rxsnr = pofdm_buf->rxsnr_X[i];
rx_snrX = (char)(tmp_rxsnr);
rx_snrX /= 2;
@@ -4499,34 +4541,39 @@ static void rtl8192_query_rxphystatus(struct r8192_priv *priv,
}
- //
- // (2)PWDB, Average PWDB cacluated by hardware (for rate adaptive)
- //
- //Fixed by Jacken from Bryant 2008-03-20
- //Original value is 106
+ /*
+ * (2)PWDB, Average PWDB cacluated by hardware (for rate adaptive)
+ */
+ /* Original value is 106 */
rx_pwr_all = (((pofdm_buf->pwdb_all) >> 1)& 0x7f) -106;
pwdb_all = rtl819x_query_rxpwrpercentage(rx_pwr_all);
pstats->RxPWDBAll = precord_stats->RxPWDBAll = pwdb_all;
pstats->RxPower = precord_stats->RxPower = rx_pwr_all;
- //
- // (3)EVM of HT rate
- //
+ /*
+ * (3)EVM of HT rate
+ */
if (pdrvinfo->RxHT && pdrvinfo->RxRate >= DESC90_RATEMCS8 &&
pdrvinfo->RxRate <= DESC90_RATEMCS15)
- max_spatial_stream = 2; //both spatial stream make sense
+ /* both spatial stream make sense */
+ max_spatial_stream = 2;
else
- max_spatial_stream = 1; //only spatial stream 1 makes sense
+ /* only spatial stream 1 makes sense */
+ max_spatial_stream = 1;
for (i = 0; i < max_spatial_stream; i++) {
tmp_rxevm = pofdm_buf->rxevm_X[i];
rx_evmX = (char)(tmp_rxevm);
- // Do not use shift operation like "rx_evmX >>= 1" because the compiler of free build environment
- // will set the most significant bit to "zero" when doing shifting operation which may change a negative
- // value to positive one, then the dbm value (which is supposed to be negative) is not correct anymore.
- rx_evmX /= 2; //dbm
+ /* Do not use shift operation like "rx_evmX >>= 1"
+ * because the compiler of free build environment
+ * will set the most significant bit to "zero" when
+ * doing shifting operation which may change a negative
+ * value to positive one, then the dbm value (which is
+ * supposed to be negative) is not correct anymore.
+ */
+ rx_evmX /= 2; /* dbm */
evm = rtl819x_evm_dbtopercentage(rx_evmX);
if (i == 0) /* Fill value in RFD, Get the first spatial stream only */
@@ -4540,16 +4587,18 @@ static void rtl8192_query_rxphystatus(struct r8192_priv *priv,
prxsc = (phy_ofdm_rx_status_rxsc_sgien_exintfflag *)&rxsc_sgien_exflg;
if (pdrvinfo->BW) /* 40M channel */
priv->stats.received_bwtype[1+prxsc->rxsc]++;
- else //20M channel
+ else /* 20M channel */
priv->stats.received_bwtype[0]++;
}
- //UI BSS List signal strength(in percentage), make it good looking, from 0~100.
- //It is assigned to the BSS List in GetValueFromBeaconOrProbeRsp().
+ /* UI BSS List signal strength(in percentage), make it good looking,
+ * from 0~100. It is assigned to the BSS List in
+ * GetValueFromBeaconOrProbeRsp().
+ */
if (is_cck_rate) {
pstats->SignalStrength = precord_stats->SignalStrength = (u8)(rtl819x_signal_scale_mapping((long)pwdb_all));
} else {
- // We can judge RX path number now.
+ /* We can judge RX path number now. */
if (rf_rx_num != 0)
pstats->SignalStrength = precord_stats->SignalStrength = (u8)(rtl819x_signal_scale_mapping((long)(total_rssi /= rf_rx_num)));
}
@@ -4568,7 +4617,7 @@ static void TranslateRxSignalStuff819xUsb(struct sk_buff *skb,
struct ieee80211_rx_stats *pstats,
rx_drvinfo_819x_usb *pdrvinfo)
{
- // TODO: We must only check packet for current MAC address. Not finish
+ /* TODO: We must only check packet for current MAC address. Not finish*/
rtl8192_rx_info *info = (struct rtl8192_rx_info *)skb->cb;
struct net_device *dev = info->dev;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
@@ -4578,7 +4627,7 @@ static void TranslateRxSignalStuff819xUsb(struct sk_buff *skb,
struct ieee80211_hdr_3addr *hdr;//by amy
u16 fc, type;
- // Get Signal Quality for only RX data queue (but not command queue)
+ /* Get Signal Quality for only RX data queue (but not command queue) */
u8 *tmp_buf;
u8 *praddr;
@@ -4610,11 +4659,12 @@ static void TranslateRxSignalStuff819xUsb(struct sk_buff *skb,
priv->stats.numpacket_matchbssid++;
if (bpacket_toself)
priv->stats.numpacket_toself++;
- //
- // Process PHY information for previous packet (RSSI/PWDB/EVM)
- //
- // Because phy information is contained in the last packet of AMPDU only, so driver
- // should process phy information of previous packet
+ /*
+ * Process PHY information for previous packet (RSSI/PWDB/EVM)
+ *
+ * Because phy information is contained in the last packet of AMPDU only, so driver
+ * should process phy information of previous packet
+ */
rtl8192_process_phyinfo(priv, tmp_buf, &previous_stats, pstats);
rtl8192_query_rxphystatus(priv, pstats, pdrvinfo, &previous_stats, bpacket_match_bssid, bpacket_toself, bPacketBeacon, bToSelfBA);
rtl8192_record_rxdesc_forlateruse(pstats, &previous_stats);
@@ -4640,9 +4690,11 @@ UpdateReceivedRateHistogramStatistics8190(struct net_device *dev,
struct ieee80211_rx_stats *stats)
{
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
- u32 rcvType = 1; //0: Total, 1:OK, 2:CRC, 3:ICV
+ /* 0: Total, 1:OK, 2:CRC, 3:ICV */
+ u32 rcvType = 1;
u32 rateIndex;
- u32 preamble_guardinterval; //1: short preamble/GI, 0: long preamble/GI
+ /* 1: short preamble/GI, 0: long preamble/GI */
+ u32 preamble_guardinterval;
if (stats->bCRC)
@@ -4651,14 +4703,14 @@ UpdateReceivedRateHistogramStatistics8190(struct net_device *dev,
rcvType = 3;
if (stats->bShortPreamble)
- preamble_guardinterval = 1;// short
+ preamble_guardinterval = 1; /* short */
else
- preamble_guardinterval = 0;// long
+ preamble_guardinterval = 0; /* long */
switch (stats->rate) {
- //
- // CCK rate
- //
+ /*
+ * CCK rate
+ */
case MGN_1M:
rateIndex = 0;
break;
@@ -4671,9 +4723,9 @@ UpdateReceivedRateHistogramStatistics8190(struct net_device *dev,
case MGN_11M:
rateIndex = 3;
break;
- //
- // Legacy OFDM rate
- //
+ /*
+ * Legacy OFDM rate
+ */
case MGN_6M:
rateIndex = 4;
break;
@@ -4698,9 +4750,9 @@ UpdateReceivedRateHistogramStatistics8190(struct net_device *dev,
case MGN_54M:
rateIndex = 11;
break;
- //
- // 11n High throughput rate
- //
+ /*
+ * 11n High throughput rate
+ */
case MGN_MCS0:
rateIndex = 12;
break;
@@ -4754,7 +4806,7 @@ UpdateReceivedRateHistogramStatistics8190(struct net_device *dev,
break;
}
priv->stats.received_preamble_GI[preamble_guardinterval][rateIndex]++;
- priv->stats.received_rate_histogram[0][rateIndex]++; //total
+ priv->stats.received_rate_histogram[0][rateIndex]++; /* total */
priv->stats.received_rate_histogram[rcvType][rateIndex]++;
}
@@ -4768,19 +4820,22 @@ static void query_rxdesc_status(struct sk_buff *skb,
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
rx_drvinfo_819x_usb *driver_info = NULL;
- //
- //Get Rx Descriptor Information
- //
+ /*
+ *Get Rx Descriptor Information
+ */
#ifdef USB_RX_AGGREGATION_SUPPORT
if (bIsRxAggrSubframe) {
rx_desc_819x_usb_aggr_subframe *desc = (rx_desc_819x_usb_aggr_subframe *)skb->data;
stats->Length = desc->Length;
stats->RxDrvInfoSize = desc->RxDrvInfoSize;
- stats->RxBufShift = 0; //RxBufShift = 2 in RxDesc, but usb didn't shift bytes in fact.
+ /* RxBufShift = 2 in RxDesc but usb didn't shift bytes in fact*/
+ stats->RxBufShift = 0;
stats->bICV = desc->ICV;
stats->bCRC = desc->CRC32;
stats->bHwError = stats->bCRC|stats->bICV;
- stats->Decrypted = !desc->SWDec;//RTL8190 set this bit to indicate that Hw does not decrypt packet
+ /* RTL8190 set this bit to indicate that Hw does not decrypt
+ * packet */
+ stats->Decrypted = !desc->SWDec;
} else
#endif
{
@@ -4792,7 +4847,8 @@ static void query_rxdesc_status(struct sk_buff *skb,
stats->bICV = desc->ICV;
stats->bCRC = desc->CRC32;
stats->bHwError = stats->bCRC|stats->bICV;
- //RTL8190 set this bit to indicate that Hw does not decrypt packet
+ /* RTL8190 set this bit to indicate that Hw does not decrypt
+ * packet */
stats->Decrypted = !desc->SWDec;
}
@@ -4803,11 +4859,11 @@ static void query_rxdesc_status(struct sk_buff *skb,
if (stats->Length < 24 || stats->Length > MAX_8192U_RX_SIZE)
stats->bHwError |= 1;
- //
- //Get Driver Info
- //
- // TODO: Need to verify it on FGPA platform
- //Driver info are written to the RxBuffer following rx desc
+ /*
+ *Get Driver Info
+ */
+ /* TODO: Need to verify it on FGPA platform */
+ /* Driver info are written to the RxBuffer following rx desc */
if (stats->RxDrvInfoSize != 0) {
driver_info = (rx_drvinfo_819x_usb *)(skb->data + sizeof(rx_desc_819x_usb) +
stats->RxBufShift);
@@ -4817,11 +4873,13 @@ static void query_rxdesc_status(struct sk_buff *skb,
u8 ret_rate;
ret_rate = HwRateToMRate90(driver_info->RxHT, driver_info->RxRate);
if (ret_rate == 0xff) {
- // Abnormal Case: Receive CRC OK packet with Rx descriptor indicating non supported rate.
- // Special Error Handling here, 2008.05.16, by Emily
+ /* Abnormal Case: Receive CRC OK packet with Rx
+ * descriptor indicating non supported rate.
+ * Special Error Handling here */
stats->bHwError = 1;
- stats->rate = MGN_1M; //Set 1M rate by default
+ /* Set 1M rate by default */
+ stats->rate = MGN_1M;
} else {
stats->rate = ret_rate;
}
@@ -4837,13 +4895,13 @@ static void query_rxdesc_status(struct sk_buff *skb,
stats->bIsAMPDU = (driver_info->PartAggr == 1);
stats->bFirstMPDU = (driver_info->PartAggr == 1) && (driver_info->FirstAGGR == 1);
stats->TimeStampLow = driver_info->TSFL;
- // xiong mask it, 070514
+ /* mask it */
UpdateRxPktTimeStamp8190(dev, stats);
- //
- // Rx A-MPDU
- //
+ /*
+ * Rx A-MPDU
+ */
if (driver_info->FirstAGGR == 1 || driver_info->PartAggr == 1)
RT_TRACE(COMP_RXDESC, "driver_info->FirstAGGR = %d, driver_info->PartAggr = %d\n",
driver_info->FirstAGGR, driver_info->PartAggr);
@@ -4851,9 +4909,9 @@ static void query_rxdesc_status(struct sk_buff *skb,
}
skb_pull(skb, sizeof(rx_desc_819x_usb));
- //
- // Get Total offset of MPDU Frame Body
- //
+ /*
+ * Get Total offset of MPDU Frame Body
+ */
if ((stats->RxBufShift + stats->RxDrvInfoSize) > 0) {
stats->bShift = 1;
skb_pull(skb, stats->RxBufShift + stats->RxDrvInfoSize);
@@ -4864,9 +4922,6 @@ static void query_rxdesc_status(struct sk_buff *skb,
if (bIsRxAggrSubframe)
skb_pull(skb, 8);
#endif
- /* for debug 2008.5.29 */
-
- //added by vivi, for MP, 20080108
stats->RxIs40MHzPacket = driver_info->BW;
if (stats->RxDrvInfoSize != 0)
TranslateRxSignalStuff819xUsb(skb, stats, driver_info);
@@ -4909,7 +4964,7 @@ static void rtl8192_rx_nomal(struct sk_buff *skb)
u32 PacketShiftBytes = 0;
rx_desc_819x_usb_aggr_subframe *RxDescr = NULL;
u8 PaddingBytes = 0;
- //add just for testing
+ /* add just for testing */
u8 testing;
#endif
@@ -4942,9 +4997,9 @@ static void rtl8192_rx_nomal(struct sk_buff *skb)
ieee80211_hdr = (struct ieee80211_hdr_1addr *)skb->data;
unicast_packet = false;
if (is_broadcast_ether_addr(ieee80211_hdr->addr1)) {
- //TODO
+ /* TODO */
} else if (is_multicast_ether_addr(ieee80211_hdr->addr1)) {
- //TODO
+ /* TODO */
} else {
/* unicast packet */
unicast_packet = true;
@@ -4998,9 +5053,9 @@ static void rtl8192_rx_nomal(struct sk_buff *skb)
ieee80211_hdr = (struct ieee80211_hdr_1addr *)skb->data;
unicast_packet = false;
if (is_broadcast_ether_addr(ieee80211_hdr->addr1)) {
- //TODO
+ /* TODO */
} else if (is_multicast_ether_addr(ieee80211_hdr->addr1)) {
- //TODO
+ /* TODO */
} else {
/* unicast packet */
unicast_packet = true;
@@ -5042,20 +5097,19 @@ static void rtl819xusb_process_received_packet(struct net_device *dev,
u16 frame_len = 0;
struct r8192_priv *priv = ieee80211_priv(dev);
- // Get shifted bytes of Starting address of 802.11 header. 2006.09.28, by Emily
- //porting by amy 080508
+ /* Get shifted bytes of Starting address of 802.11 header. */
pstats->virtual_address += get_rxpacket_shiftbytes_819xusb(pstats);
frame = pstats->virtual_address;
frame_len = pstats->packetlength;
-#ifdef TODO // by amy about HCT
+#ifdef TODO /* about HCT */
if (!Adapter->bInHctTest)
CountRxErrStatistics(Adapter, pRfd);
#endif
-#ifdef ENABLE_PS //by amy for adding ps function in future
+#ifdef ENABLE_PS /* for adding ps function in future */
RT_RF_POWER_STATE rtState;
- // When RF is off, we should not count the packet for hw/sw synchronize
- // reason, ie. there may be a duration while sw switch is changed and hw
- // switch is being changed. 2006.12.04, by shien chang.
+ /* When RF is off, we should not count the packet for hw/sw synchronize
+ * reason, ie. there may be a duration while sw switch is changed and hw
+ * switch is being changed. 2006.12.04, by shien chang. */
Adapter->HalFunc.GetHwRegHandler(Adapter, HW_VAR_RF_STATE, (u8 *)(&rtState));
if (rtState == eRfOff)
return;
@@ -5082,9 +5136,9 @@ static void query_rx_cmdpkt_desc_status(struct sk_buff *skb,
{
rx_desc_819x_usb *desc = (rx_desc_819x_usb *)skb->data;
- //
- //Get Rx Descriptor Information
- //
+ /*
+ *Get Rx Descriptor Information
+ */
stats->virtual_address = (u8 *)skb->data;
stats->Length = desc->Length;
stats->RxDrvInfoSize = 0;
@@ -5111,12 +5165,12 @@ static void rtl8192_rx_cmd(struct sk_buff *skb)
if ((skb->len >= (20 + sizeof(rx_desc_819x_usb))) && (skb->len < RX_URB_SIZE)) {
query_rx_cmdpkt_desc_status(skb, &stats);
- // this is to be done by amy 080508 prfd->queue_id = 1;
+ /* this is to be done by amy 080508 prfd->queue_id = 1; */
- //
- // Process the command packet received.
- //
+ /*
+ * Process the command packet received.
+ */
rtl819xusb_process_received_packet(dev, &stats);
@@ -5199,7 +5253,7 @@ static int rtl8192_usb_probe(struct usb_interface *intf,
dev->type = ARPHRD_ETHER;
- dev->watchdog_timeo = HZ*3; //modified by john, 0805
+ dev->watchdog_timeo = HZ*3;
if (dev_alloc_name(dev, ifname) < 0) {
RT_TRACE(COMP_INIT, "Oops: devname already taken! Trying wlan%%d...\n");
@@ -5241,7 +5295,8 @@ fail:
return ret;
}
-//detach all the work and timer structure declared or inititialize in r8192U_init function.
+/* detach all the work and timer structure declared or inititialize in
+ * r8192U_init function. */
void rtl8192_cancel_deferred_work(struct r8192_priv *priv)
{
@@ -5367,8 +5422,12 @@ void EnableHWSecurityConfig8192(struct net_device *dev)
SECR_value |= SCR_RxUseDK;
SECR_value |= SCR_TxUseDK;
}
- //add HWSec active enable here.
- //default using hwsec. when peer AP is in N mode only and pairwise_key_type is none_aes(which HT_IOT_ACT_PURE_N_MODE indicates it), use software security. when peer AP is in b,g,n mode mixed and pairwise_key_type is none_aes, use g mode hw security. WB on 2008.7.4
+ /* add HWSec active enable here.
+ * default using hwsec. when peer AP is in N mode only and
+ * pairwise_key_type is none_aes(which HT_IOT_ACT_PURE_N_MODE indicates
+ * it), use software security. when peer AP is in b,g,n mode mixed and
+ * pairwise_key_type is none_aes, use g mode hw security.
+ */
ieee->hwsec_active = 1;
@@ -5419,7 +5478,7 @@ void setKey(struct net_device *dev, u8 EntryNo, u8 KeyIndex, u16 KeyType,
write_nic_dword(dev, WCAMI, TargetContent);
write_nic_dword(dev, RWCAM, TargetCommand);
} else {
- //Key Material
+ /* Key Material */
if (KeyContent != NULL) {
write_nic_dword(dev, WCAMI, (u32)(*(KeyContent+i-2)));
write_nic_dword(dev, RWCAM, TargetCommand);
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/