Re: [PATCH v3 1/2] arm64: dts: fsl: pico-pi: Add a device tree for the PICO-PI-IMX8M

[Andra Danciu]

Hi Fabio,

Please find my answers inline:

Ãn vin., 19 iul. 2019 la 02:05, Fabio Estevam <festevam@xxxxxxxxx> a scris:
>
> Hi Andra,
>
> On Thu, Jul 18, 2019 at 9:16 AM Andra Danciu <andradanciu1997@xxxxxxxxx> wrote:
> >
> > From: Richard Hu <richard.hu@xxxxxxxxxxxxxx>
>
> Please put a few words about the board and a link to its webpage, if available.
OK
>
> > The current level of support yields a working console and is able to boot
> > userspace from NFS or init ramdisk.
> >
> > Additional subsystems that are active :
> >         - Ethernet
> >         - USB
> >
> > Cc: Daniel Baluta <daniel.baluta@xxxxxxx>
> > Signed-off-by: Richard Hu <richard.hu@xxxxxxxxxxxxxx>
> > Signed-off-by: Andra Danciu <andradanciu1997@xxxxxxxxx>
> > ---
> >  arch/arm64/boot/dts/freescale/Makefile       |   1 +
> >  arch/arm64/boot/dts/freescale/pico-pi-8m.dts | 417 +++++++++++++++++++++++++++
> >  2 files changed, 418 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/freescale/pico-pi-8m.dts
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index c043aca66572..538422903e8a 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -26,3 +26,4 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
> > +dtb-$(CONFIG_ARCH_MXC) += pico-pi-8m.dtb
>
> The convention we use with imx dtbs is to put the SoC name first, so
> that would become:
>
> imx8mq-pico-pi.dtb
Will do.
>
>
> > +&iomuxc {
>
> Please place iomuxc node as the last one.
Will do.
>
> > +&fec1 {
> > +       pinctrl-names = "default";
> > +       pinctrl-0 = <&pinctrl_fec1 &pinctrl_enet_3v3>;
> > +       phy-mode = "rgmii-id";
> > +       pinctrl-assert-gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
>
> This property does not exist.
OK, I will remove it.
>
> > +       phy-handle = <&ethphy0>;
> > +       fsl,magic-packet;
> > +       status = "okay";
> > +
> > +       mdio {
> > +               #address-cells = <1>;
> > +               #size-cells = <0>;
> > +
> > +               ethphy0: ethernet-phy@1 {
> > +                       compatible = "ethernet-phy-ieee802.3-c22";
> > +                       reg = <1>;
> > +                       at803x,led-act-blind-workaround;
> > +                       at803x,eee-disabled;
>
> These two properties do not exist.
OK, I will remove them.
>
> > +&i2c1 {
> > +       clock-frequency = <100000>;
> > +       pinctrl-names = "default";
> > +       pinctrl-0 = <&pinctrl_i2c1>;
> > +       status = "okay";
> > +
> > +       pmic: pmic@4b {
> > +               reg = <0x4b>;
> > +               compatible = "rohm,bd71837";
> > +               /* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
> > +               pinctrl-0 = <&pinctrl_pmic>;
>
> pinctrl-names = "default" is missing
OK, will add.
>
> > +               gpio_intr = <&gpio1 3 GPIO_ACTIVE_LOW>;
>
> This is not documented.
>
> Please look at Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
> for the valid bindings and also at
> arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts for a
> reference for adding the BD71837 support.
OK, will do.
>
> > +&A53_0 {
> > +       operating-points = <
> > +               /* kHz    uV */
> > +               1500000 1000000
> > +               1300000 1000000
> > +               1000000 900000
> > +               800000  900000
>
> This is not needed as these operating points are already specified at
> imx8mq.dtsi.
OK, I will remove it.