[PATCH v2 1/3] mfd: stpmic1: fixup main control register and bits naming

[Sean Nyekjaer]

Fixup main control register and bits naming so the match the naming from
the datasheet.

https://www.st.com/resource/en/datasheet/stpmic1.pdf

Signed-off-by: Sean Nyekjaer <sean@xxxxxxxxxx>
---
Changes since v1:
 - None

 drivers/mfd/stpmic1.c       |  4 ++--
 include/linux/mfd/stpmic1.h | 12 ++++++------
 2 files changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/mfd/stpmic1.c b/drivers/mfd/stpmic1.c
index 8db1530d9bac..4c9b18d9dec8 100644
--- a/drivers/mfd/stpmic1.c
+++ b/drivers/mfd/stpmic1.c
@@ -19,7 +19,7 @@
 
 static const struct regmap_range stpmic1_readable_ranges[] = {
 	regmap_reg_range(TURN_ON_SR, VERSION_SR),
-	regmap_reg_range(SWOFF_PWRCTRL_CR, LDO6_STDBY_CR),
+	regmap_reg_range(MAIN_CR, LDO6_STDBY_CR),
 	regmap_reg_range(BST_SW_CR, BST_SW_CR),
 	regmap_reg_range(INT_PENDING_R1, INT_PENDING_R4),
 	regmap_reg_range(INT_CLEAR_R1, INT_CLEAR_R4),
@@ -30,7 +30,7 @@ static const struct regmap_range stpmic1_readable_ranges[] = {
 };
 
 static const struct regmap_range stpmic1_writeable_ranges[] = {
-	regmap_reg_range(SWOFF_PWRCTRL_CR, LDO6_STDBY_CR),
+	regmap_reg_range(MAIN_CR, LDO6_STDBY_CR),
 	regmap_reg_range(BST_SW_CR, BST_SW_CR),
 	regmap_reg_range(INT_CLEAR_R1, INT_CLEAR_R4),
 	regmap_reg_range(INT_SET_MASK_R1, INT_SET_MASK_R4),
diff --git a/include/linux/mfd/stpmic1.h b/include/linux/mfd/stpmic1.h
index fa3f99f7e9a1..dc00bac24f5a 100644
--- a/include/linux/mfd/stpmic1.h
+++ b/include/linux/mfd/stpmic1.h
@@ -15,7 +15,7 @@
 #define RREQ_STATE_SR		0x5
 #define VERSION_SR		0x6
 
-#define SWOFF_PWRCTRL_CR	0x10
+#define MAIN_CR			0x10
 #define PADS_PULL_CR		0x11
 #define BUCKS_PD_CR		0x12
 #define LDO14_PD_CR		0x13
@@ -148,14 +148,14 @@
 #define LDO_BYPASS_MASK			BIT(7)
 
 /* Main PMIC Control Register
- * SWOFF_PWRCTRL_CR
+ * MAIN_CR
  * Address : 0x10
  */
-#define ICC_EVENT_ENABLED		BIT(4)
+#define OCP_OFF_DBG			BIT(4)
 #define PWRCTRL_POLARITY_HIGH		BIT(3)
-#define PWRCTRL_PIN_VALID		BIT(2)
-#define RESTART_REQUEST_ENABLED		BIT(1)
-#define SOFTWARE_SWITCH_OFF_ENABLED	BIT(0)
+#define PWRCTRL_ENABLE			BIT(2)
+#define RESTART_REQUEST_ENABLE		BIT(1)
+#define SOFTWARE_SWITCH_OFF		BIT(0)
 
 /* Main PMIC PADS Control Register
  * PADS_PULL_CR
-- 
2.40.0