Re: riscv: boot failure for 3335068f8721 ("riscv: Use PUD/P4D/PGD pages for the linear mapping")

[Drew Fustini]

On Sat, May 20, 2023 at 10:22:36PM -0500, Samuel Holland wrote:
> Hi Drew,
> 
> On 5/20/23 21:05, Drew Fustini wrote:
> > Hello, I tested 6.4-rc1 on an internal RISC-V SoC and observed a boot
> > failure on a Store/AMO access fault (exception code 7) in __memset().
> > stval (e.g. badaddr) was set to 0xffffaf8000000000. This SoC is RV64GC
> > with Sv48 so it seems that address is the start of the "direct mapping
> > of all physical memory" [1].
> > 
> > The 6.3 release boots okay and the system is able to operate correctly
> > with an Ubuntu 23.04 rootfs on eMMC. Therefore, I decided to bisect and
> > I found the failure begins with 3335068f8721 ("riscv: Use PUD/P4D/PGD
> > pages for the linear mapping"). The system boots okay with the prior
> > commit 8589e346bbb6 ("riscv: Move the linear mapping creation in its
> > own function").
> > 
> > The boot log [2] shows that the fault happens right after buildroot's
> > init script [3] uses switch_root to execute init from the Ubuntu rootfs
> > on the eMMC.
> > 
> > DWARF4 is enabled in .config [4] and the decoded stack trace [5] shows:
> > 
> >   epc : __memset (/eng/dfustini/gitlab/linux/arch/riscv/lib/memset.S:67)
> > 
> > From memset.S:
> > 
> >  Line 67:         REG_S a1,        0(t0)
> > 
> > From the oops:
> > 
> >  epc : ffffffff81122d6c ra : ffffffff80218504 sp : ffffaf8002e47500
> >   gp : ffffffff82695010 tp : ffffaf8002e2ec00 t0 : ffffaf8000000000
> >   t1 : 0000000000000080 t2 : 0000000000000001 s0 : ffffaf8002e47550
> >   s1 : ffff8d8200000040 a0 : ffffaf8000000000 a1 : 0000000000000000
> > 
> > Thus I think it is trying to store 0x0 to 0xffffaf8000000000 which is
> > the start of the direct map. From the boot log [2], OpenSBI shows:
> > 
> >  Domain0 Region00 : 0x0000000002080000-0x00000000020bffff M: (I,R,W) S/U: ()
> >  Domain0 Region01 : 0x0000008000000000-0x000000800003ffff M: (R,W,X) S/U: ()
> >  Domain0 Region02 : 0x0000000002000000-0x000000000207ffff M: (I,R,W) S/U: ()
> >  Domain0 Region03 : 0x0000000000000000-0xffffffffffffffff M: (R,W,X) S/U: (R,W,X)
> > 
> > The DDR memory on this SoC starts at 0x8000000000 with size 2GB. The
> > memory node from the device tree [6]:
> > 
> >         memory@8000000000 {
> >                 device_type = "memory";
> >                 reg = <0x80 0 0x00000000 0x80000000>;
> >         };
> > 
> > I think the direct map address 0xffffaf8000000000 would map to physical
> > address 0x8000000000. Thus I think the attempted store in S-mode to that
> > address would violate the PMP settings for Region01.
> > 
> > I do not yet understand why this happens with 3335068f8721 ("riscv: Use
> > PUD/P4D/PGD pages for the linear mapping") but not for the prior commit
> > 8589e346bbb6 ("riscv: Move the linear mapping creation in its own
> > function").
> 
> Where does Linux's DTB come from? It should be the one that was modified
> by OpenSBI to add a reserved-memory node matching PMP Region01
> (fdt_reserved_memory_fixup()).
> 
> Before this commit, Linux ignored the first 2 MiB of physical RAM. So if
> OpenSBI was loaded in this region, you could get away with ignoring the
> firmware-provided DTB; now you actually need to use it, as intended.

The address of the dtb is passed by the boot code to OpenSBI. I had been
using OpenSBI master from Jan 9: 001106d ("docs: Update domain's region
permissions and requirements"). The kernel receives the device tree from
OpenSBI but I had never actually dumped it from sysfs.

I checked out the prior kernel commit 8589e346bbb6 ("riscv: Move the
linear mapping creation in its own function") and ran "dtc -I fs
/sys/firmware/devicetree/base/" to dump the device tree [1]. This showed
that the reserved-memory node was blank.

Jessica pointed out to me on #riscv irc that this was fixed in OpenSBI
on Jan 21 with: a990309 ("lib: utils: Fix reserved memory node for
firmware memory"). Therefore, I updated to the current OpenSBI master:
33f1722 ("lib: sbi: Document sbi_ecall_extension members") from May 15.
The device tree that OpenSBI passes to the kernel now has
"mmode_resv0@80,0" and "mmode_resv1@80,20000".

Furthermore, my system now boots okay with 3335068f8721 ("riscv: Use
PUD/P4D/PGD pages for the linear mapping") so the problem was just that
I had been using an OpenSBI that was slightly too old.

Thanks,
Drew

[1] https://gist.github.com/pdp7/71ca465997274e11953b26861e36144f
[2] https://gist.github.com/pdp7/90b4632146fc55625735fa288d80532b