[PATCH v2 5/6] drivers/thermal/exynos: add initial Exynos850 support
From: Mateusz Majewski
Date: Fri Jul 26 2024 - 07:03:00 EST
This is loosely adapted from an implementation available at
https://gitlab.com/Linaro/96boards/e850-96/kernel/-/blob/android-exynos-4.14-linaro/drivers/thermal/samsung/exynos_tmu.c
Some differences from that implementation:
- unlike that implementation, we do not use the ACPM mechanism, instead
we just access the registers, like we do for other SoCs,
- the SoC is supposed to support multiple sensors inside one unit. The
vendor implementation uses one kernel device per sensor, we would
probably prefer to have one device for all sensors, have
#thermal-sensor-cells = <1> and so on. We implemented this, but we
could not get the extra sensors to work on our hardware so far. This
might be due to a misconfiguration and we will probably come back to
this, however our implementation only supports a single sensor for
now,
- the vendor implementation supports disabling CPU cores as a cooling
device. We did not attempt to port this, and this would not really fit
this driver anyway.
Additionally, some differences from the other SoCs supported by this
driver:
- we do not really constrain the e-fuse information like the other SoCs
do (data->{min,max}_efuse_value). In our tests, those values (as well
as the raw sensor values) were much higher than in the other SoCs, to
the degree that reusing the data->{min,max}_efuse_value from the other
SoCs would cause instant critical temperature reset on boot,
- this SoC provides more information in the e-fuse data than other SoCs,
so we read some values inside exynos850_tmu_initialize instead of
hardcoding them in exynos_map_dt_data.
Signed-off-by: Mateusz Majewski <m.majewski2@xxxxxxxxxxx>
---
v1 -> v2: rename and reorder some registers, use the correct register
offset for EXYNOS850_TMU_REG_AVG_CON, make the clock required,
additionally do some minor style changes.
drivers/thermal/samsung/exynos_tmu.c | 191 +++++++++++++++++++++++++--
1 file changed, 182 insertions(+), 9 deletions(-)
diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
index 087a09628e23..2618a81fca53 100644
--- a/drivers/thermal/samsung/exynos_tmu.c
+++ b/drivers/thermal/samsung/exynos_tmu.c
@@ -117,6 +117,41 @@
#define EXYNOS7_EMUL_DATA_SHIFT 7
#define EXYNOS7_EMUL_DATA_MASK 0x1ff
+/* Exynos850 specific registers */
+#define EXYNOS850_TMU_REG_CURRENT_TEMP0_1 0x40
+#define EXYNOS850_TMU_REG_THD_TEMP0_RISE 0x50
+#define EXYNOS850_TMU_REG_THD_TEMP0_FALL 0x60
+
+#define EXYNOS850_TMU_TRIMINFO_SHIFT 4
+#define EXYNOS850_TMU_TRIMINFO_OFFSET(n) \
+ (EXYNOS_TMU_REG_TRIMINFO + (n) * EXYNOS850_TMU_TRIMINFO_SHIFT)
+#define EXYNOS850_TMU_T_TRIM0_SHIFT 18
+
+#define EXYNOS850_TMU_REG_CONTROL1 0x24
+#define EXYNOS850_TMU_LPI_MODE_MASK 1
+#define EXYNOS850_TMU_LPI_MODE_SHIFT 10
+
+#define EXYNOS850_TMU_REG_COUNTER_VALUE0 0x30
+#define EXYNOS850_TMU_EN_TEMP_SEN_OFF_MASK 0xffff
+#define EXYNOS850_TMU_EN_TEMP_SEN_OFF_SHIFT 0
+
+#define EXYNOS850_TMU_REG_COUNTER_VALUE1 0x34
+#define EXYNOS850_TMU_CLK_SENSE_ON_MASK 0xffff
+#define EXYNOS850_TMU_CLK_SENSE_ON_SHIFT 16
+
+#define EXYNOS850_TMU_REG_AVG_CON 0x38
+#define EXYNOS850_TMU_AVG_MODE_MASK 0x7
+#define EXYNOS850_TMU_DEM_ENABLE BIT(4)
+
+#define EXYNOS850_TMU_REG_TRIM0 0x3c
+#define EXYNOS850_TMU_TRIM0_MASK 0xf
+#define EXYNOS850_TMU_VBEI_TRIM_SHIFT 8
+#define EXYNOS850_TMU_VREF_TRIM_SHIFT 12
+#define EXYNOS850_TMU_BGRI_TRIM_SHIFT 20
+
+#define EXYNOS850_TMU_TEM1051X_SENSE_VALUE 0x028a
+#define EXYNOS850_TMU_TEM1456X_SENSE_VALUE 0x0a28
+
#define EXYNOS_FIRST_POINT_TRIM 25
#define EXYNOS_SECOND_POINT_TRIM 85
@@ -134,6 +169,7 @@ enum soc_type {
SOC_ARCH_EXYNOS5420_TRIMINFO,
SOC_ARCH_EXYNOS5433,
SOC_ARCH_EXYNOS7,
+ SOC_ARCH_EXYNOS850,
};
/**
@@ -232,12 +268,14 @@ static int code_to_temp(struct exynos_tmu_data *data, u16 temp_code)
static void sanitize_temp_error(struct exynos_tmu_data *data, u32 trim_info)
{
- u16 tmu_temp_mask =
- (data->soc == SOC_ARCH_EXYNOS7) ? EXYNOS7_TMU_TEMP_MASK
- : EXYNOS_TMU_TEMP_MASK;
- int tmu_85_shift =
- (data->soc == SOC_ARCH_EXYNOS7) ? EXYNOS7_TMU_TEMP_SHIFT
- : EXYNOS_TRIMINFO_85_SHIFT;
+ u16 tmu_temp_mask = (data->soc == SOC_ARCH_EXYNOS7 ||
+ data->soc == SOC_ARCH_EXYNOS850) ?
+ EXYNOS7_TMU_TEMP_MASK :
+ EXYNOS_TMU_TEMP_MASK;
+ int tmu_85_shift = (data->soc == SOC_ARCH_EXYNOS7 ||
+ data->soc == SOC_ARCH_EXYNOS850) ?
+ EXYNOS7_TMU_TEMP_SHIFT :
+ EXYNOS_TRIMINFO_85_SHIFT;
data->temp_error1 = trim_info & tmu_temp_mask;
if (!data->temp_error1 ||
@@ -587,6 +625,114 @@ static void exynos7_tmu_initialize(struct platform_device *pdev)
sanitize_temp_error(data, trim_info);
}
+static void exynos850_tmu_set_low_temp(struct exynos_tmu_data *data, u8 temp)
+{
+ exynos_tmu_update_temp(data, EXYNOS850_TMU_REG_THD_TEMP0_FALL + 12, 0,
+ temp);
+ exynos_tmu_update_bit(data, EXYNOS7_TMU_REG_INTEN,
+ EXYNOS_TMU_INTEN_FALL0_SHIFT + 0, true);
+}
+
+static void exynos850_tmu_set_high_temp(struct exynos_tmu_data *data, u8 temp)
+{
+ exynos_tmu_update_temp(data, EXYNOS850_TMU_REG_THD_TEMP0_RISE + 12, 16,
+ temp);
+ exynos_tmu_update_bit(data, EXYNOS7_TMU_REG_INTEN,
+ EXYNOS7_TMU_INTEN_RISE0_SHIFT + 1, true);
+}
+
+static void exynos850_tmu_disable_low(struct exynos_tmu_data *data)
+{
+ exynos_tmu_update_bit(data, EXYNOS7_TMU_REG_INTEN,
+ EXYNOS_TMU_INTEN_FALL0_SHIFT + 0, false);
+}
+
+static void exynos850_tmu_disable_high(struct exynos_tmu_data *data)
+{
+ exynos_tmu_update_bit(data, EXYNOS7_TMU_REG_INTEN,
+ EXYNOS7_TMU_INTEN_RISE0_SHIFT + 1, false);
+}
+
+static void exynos850_tmu_set_crit_temp(struct exynos_tmu_data *data, u8 temp)
+{
+ exynos_tmu_update_temp(data, EXYNOS850_TMU_REG_THD_TEMP0_RISE + 0, 16,
+ temp);
+ exynos_tmu_update_bit(data, EXYNOS_TMU_REG_CONTROL,
+ EXYNOS_TMU_THERM_TRIP_EN_SHIFT, true);
+ exynos_tmu_update_bit(data, EXYNOS7_TMU_REG_INTEN,
+ EXYNOS7_TMU_INTEN_RISE0_SHIFT + 7, true);
+}
+
+static void exynos850_tmu_initialize(struct platform_device *pdev)
+{
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ u32 cal_type, avg_mode, reg, bgri, vref, vbei;
+
+ reg = readl(data->base + EXYNOS850_TMU_TRIMINFO_OFFSET(0));
+ cal_type = (reg & EXYNOS5433_TRIMINFO_CALIB_SEL_MASK) >>
+ EXYNOS5433_TRIMINFO_CALIB_SEL_SHIFT;
+ data->reference_voltage = (reg >> EXYNOS850_TMU_T_TRIM0_SHIFT) &
+ EXYNOS_TMU_REF_VOLTAGE_MASK;
+ reg = readl(data->base + EXYNOS850_TMU_TRIMINFO_OFFSET(1));
+ data->gain = (reg >> EXYNOS850_TMU_T_TRIM0_SHIFT) &
+ EXYNOS_TMU_BUF_SLOPE_SEL_MASK;
+ reg = readl(data->base + EXYNOS850_TMU_TRIMINFO_OFFSET(2));
+ avg_mode = (reg >> EXYNOS850_TMU_T_TRIM0_SHIFT) &
+ EXYNOS850_TMU_AVG_MODE_MASK;
+ reg = readl(data->base + EXYNOS850_TMU_TRIMINFO_OFFSET(3));
+ bgri = (reg >> EXYNOS850_TMU_T_TRIM0_SHIFT) & EXYNOS850_TMU_TRIM0_MASK;
+ reg = readl(data->base + EXYNOS850_TMU_TRIMINFO_OFFSET(4));
+ vref = (reg >> EXYNOS850_TMU_T_TRIM0_SHIFT) & EXYNOS850_TMU_TRIM0_MASK;
+ reg = readl(data->base + EXYNOS850_TMU_TRIMINFO_OFFSET(5));
+ vbei = (reg >> EXYNOS850_TMU_T_TRIM0_SHIFT) & EXYNOS850_TMU_TRIM0_MASK;
+
+ data->cal_type = cal_type == EXYNOS5433_TRIMINFO_TWO_POINT_TRIMMING ?
+ TYPE_TWO_POINT_TRIMMING :
+ TYPE_ONE_POINT_TRIMMING;
+
+ reg = readl(data->base + EXYNOS850_TMU_TRIMINFO_OFFSET(0));
+ sanitize_temp_error(data, reg);
+
+ dev_info(&pdev->dev, "Calibration type is %d-point calibration\n",
+ cal_type ? 2 : 1);
+
+ reg = readl(data->base + EXYNOS850_TMU_REG_AVG_CON);
+ reg &= ~EXYNOS850_TMU_AVG_MODE_MASK;
+ reg &= ~EXYNOS850_TMU_DEM_ENABLE;
+ if (avg_mode) {
+ reg |= avg_mode;
+ reg |= EXYNOS850_TMU_DEM_ENABLE;
+ }
+ writel(reg, data->base + EXYNOS850_TMU_REG_AVG_CON);
+
+ reg = readl(data->base + EXYNOS850_TMU_REG_COUNTER_VALUE0);
+ reg &= ~(EXYNOS850_TMU_EN_TEMP_SEN_OFF_MASK
+ << EXYNOS850_TMU_EN_TEMP_SEN_OFF_SHIFT);
+ reg |= EXYNOS850_TMU_TEM1051X_SENSE_VALUE
+ << EXYNOS850_TMU_EN_TEMP_SEN_OFF_SHIFT;
+ writel(reg, data->base + EXYNOS850_TMU_REG_COUNTER_VALUE0);
+
+ reg = readl(data->base + EXYNOS850_TMU_REG_COUNTER_VALUE1);
+ reg &= ~(EXYNOS850_TMU_CLK_SENSE_ON_MASK
+ << EXYNOS850_TMU_CLK_SENSE_ON_SHIFT);
+ reg |= EXYNOS850_TMU_TEM1051X_SENSE_VALUE
+ << EXYNOS850_TMU_CLK_SENSE_ON_SHIFT;
+ writel(reg, data->base + EXYNOS850_TMU_REG_COUNTER_VALUE1);
+
+ reg = readl(data->base + EXYNOS850_TMU_REG_TRIM0);
+ reg &= ~(EXYNOS850_TMU_TRIM0_MASK << EXYNOS850_TMU_BGRI_TRIM_SHIFT);
+ reg &= ~(EXYNOS850_TMU_TRIM0_MASK << EXYNOS850_TMU_VREF_TRIM_SHIFT);
+ reg &= ~(EXYNOS850_TMU_TRIM0_MASK << EXYNOS850_TMU_VBEI_TRIM_SHIFT);
+ reg |= bgri << EXYNOS850_TMU_BGRI_TRIM_SHIFT;
+ reg |= vref << EXYNOS850_TMU_VREF_TRIM_SHIFT;
+ reg |= vbei << EXYNOS850_TMU_VBEI_TRIM_SHIFT;
+ writel(reg, data->base + EXYNOS850_TMU_REG_TRIM0);
+
+ reg = readl(data->base + EXYNOS850_TMU_REG_CONTROL1);
+ reg &= ~(EXYNOS850_TMU_LPI_MODE_MASK << EXYNOS850_TMU_LPI_MODE_SHIFT);
+ writel(reg, data->base + EXYNOS850_TMU_REG_CONTROL1);
+}
+
static void exynos4210_tmu_control(struct platform_device *pdev, bool on)
{
struct exynos_tmu_data *data = platform_get_drvdata(pdev);
@@ -676,7 +822,8 @@ static u32 get_emul_con_reg(struct exynos_tmu_data *data, unsigned int val,
val &= ~(EXYNOS_EMUL_TIME_MASK << EXYNOS_EMUL_TIME_SHIFT);
val |= (EXYNOS_EMUL_TIME << EXYNOS_EMUL_TIME_SHIFT);
- if (data->soc == SOC_ARCH_EXYNOS7) {
+ if (data->soc == SOC_ARCH_EXYNOS7 ||
+ data->soc == SOC_ARCH_EXYNOS850) {
val &= ~(EXYNOS7_EMUL_DATA_MASK <<
EXYNOS7_EMUL_DATA_SHIFT);
val |= (temp_to_code(data, temp) <<
@@ -706,7 +853,8 @@ static void exynos4412_tmu_set_emulation(struct exynos_tmu_data *data,
emul_con = EXYNOS5260_EMUL_CON;
else if (data->soc == SOC_ARCH_EXYNOS5433)
emul_con = EXYNOS5433_TMU_EMUL_CON;
- else if (data->soc == SOC_ARCH_EXYNOS7)
+ else if (data->soc == SOC_ARCH_EXYNOS7 ||
+ data->soc == SOC_ARCH_EXYNOS850)
emul_con = EXYNOS7_TMU_REG_EMUL_CON;
else
emul_con = EXYNOS_EMUL_CON;
@@ -761,6 +909,12 @@ static int exynos7_tmu_read(struct exynos_tmu_data *data)
EXYNOS7_TMU_TEMP_MASK;
}
+static int exynos850_tmu_read(struct exynos_tmu_data *data)
+{
+ return readw(data->base + EXYNOS850_TMU_REG_CURRENT_TEMP0_1) &
+ EXYNOS7_TMU_TEMP_MASK;
+}
+
static irqreturn_t exynos_tmu_threaded_irq(int irq, void *id)
{
struct exynos_tmu_data *data = id;
@@ -787,7 +941,8 @@ static void exynos4210_tmu_clear_irqs(struct exynos_tmu_data *data)
if (data->soc == SOC_ARCH_EXYNOS5260) {
tmu_intstat = EXYNOS5260_TMU_REG_INTSTAT;
tmu_intclear = EXYNOS5260_TMU_REG_INTCLEAR;
- } else if (data->soc == SOC_ARCH_EXYNOS7) {
+ } else if (data->soc == SOC_ARCH_EXYNOS7 ||
+ data->soc == SOC_ARCH_EXYNOS850) {
tmu_intstat = EXYNOS7_TMU_REG_INTPEND;
tmu_intclear = EXYNOS7_TMU_REG_INTPEND;
} else if (data->soc == SOC_ARCH_EXYNOS5433) {
@@ -838,6 +993,9 @@ static const struct of_device_id exynos_tmu_match[] = {
}, {
.compatible = "samsung,exynos7-tmu",
.data = (const void *)SOC_ARCH_EXYNOS7,
+ }, {
+ .compatible = "samsung,exynos850-tmu",
+ .data = (const void *)SOC_ARCH_EXYNOS850,
},
{ },
};
@@ -950,6 +1108,21 @@ static int exynos_map_dt_data(struct platform_device *pdev)
data->min_efuse_value = 15;
data->max_efuse_value = 100;
break;
+ case SOC_ARCH_EXYNOS850:
+ data->tmu_set_low_temp = exynos850_tmu_set_low_temp;
+ data->tmu_set_high_temp = exynos850_tmu_set_high_temp;
+ data->tmu_disable_low = exynos850_tmu_disable_low;
+ data->tmu_disable_high = exynos850_tmu_disable_high;
+ data->tmu_set_crit_temp = exynos850_tmu_set_crit_temp;
+ data->tmu_initialize = exynos850_tmu_initialize;
+ data->tmu_control = exynos4210_tmu_control;
+ data->tmu_read = exynos850_tmu_read;
+ data->tmu_set_emulation = exynos4412_tmu_set_emulation;
+ data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
+ data->efuse_value = 55;
+ data->min_efuse_value = 0;
+ data->max_efuse_value = 511;
+ break;
default:
dev_err(&pdev->dev, "Platform not supported\n");
return -EINVAL;
--
2.45.1