Re: [PATCH 1/1] dt-bindings: switch: adg1712: add ADG1712 SPST switch binding

[Rob Herring (Arm)]

On Fri, 28 Nov 2025 16:46:13 +0200, Antoniu Miclaus wrote:
> Add devicetree bindings for the ADG1712 quad SPST switch.
> 
> The ADG1712 contains four independent single-pole, single-throw (SPST)
> switches, each controlled by a dedicated GPIO pin. While the device
> uses the existing gpio-mux driver infrastructure (as each switch can be
> modeled as a simple 2-state mux), a dedicated binding document is needed
> to provide clear documentation on how to properly represent the ADG1712
> in devicetree, following the pattern of one mux-controller node per
> independent switch.
> 
> The binding references the gpio-mux schema and demonstrates how each of
> the four independent switches should be instantiated as separate
> mux-controller nodes in the devicetree.
> 
> Signed-off-by: Antoniu Miclaus <antoniu.miclaus@xxxxxxxxxx>
> ---
>  .../bindings/switch/adi,adg1712.yaml          | 63 +++++++++++++++++++
>  1 file changed, 63 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/switch/adi,adg1712.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/thermal/thermal-zones.example.dtb: /example-0/soc/thermal-sensor@c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-zones.example.dtb: /example-0/soc/thermal-sensor@c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-zones.example.dtb: /example-0/soc/thermal-sensor@c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-zones.example.dtb: /example-0/soc/thermal-sensor@c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20251128144627.24910-2-antoniu.miclaus@xxxxxxxxxx

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.