Re: [PATCH v3 1/2] PM / devfreq: Generic CPU frequency to device frequency mapping governor

[Rob Herring]

On Wed, Aug 01, 2018 at 05:57:41PM -0700, Saravana Kannan wrote:
> Many CPU architectures have caches that can scale independent of the CPUs.
> Frequency scaling of the caches is necessary to make sure the cache is not
> a performance bottleneck that leads to poor performance and power. The same
> idea applies for RAM/DDR.
> 
> To achieve this, this patch adds a generic devfreq governor that takes the
> current frequency of each CPU frequency domain and then adjusts the
> frequency of the cache (or any devfreq device) based on the frequency of
> the CPUs. It listens to CPU frequency transition notifiers to keep itself
> up to date on the current CPU frequency.
> 
> To decide the frequency of the device, the governor does one of the
> following:
> 
> * Uses a CPU frequency to device frequency mapping table
>   - Either one mapping table used for all CPU freq policies (typically used
>     for system with homogeneous cores/clusters that have the same OPPs).
>   - One mapping table per CPU freq policy (typically used for ASMP systems
>     with heterogeneous CPUs with different OPPs)
> 
> OR
> 
> * Scales the device frequency in proportion to the CPU frequency. So, if
>   the CPUs are running at their max frequency, the device runs at its max
>   frequency.  If the CPUs are running at their min frequency, the device
>   runs at its min frequency. And interpolated for frequencies in between.
> 
> Signed-off-by: Saravana Kannan <skannan@xxxxxxxxxxxxxx>
> ---
>  .../bindings/devfreq/devfreq-cpufreq-map.txt       |  53 ++

Bindings should be a separate patch.

>  drivers/devfreq/Kconfig                            |   8 +
>  drivers/devfreq/Makefile                           |   1 +
>  drivers/devfreq/governor_cpufreq_map.c             | 583 +++++++++++++++++++++
>  4 files changed, 645 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/devfreq/devfreq-cpufreq-map.txt
>  create mode 100644 drivers/devfreq/governor_cpufreq_map.c
> 
> diff --git a/Documentation/devicetree/bindings/devfreq/devfreq-cpufreq-map.txt b/Documentation/devicetree/bindings/devfreq/devfreq-cpufreq-map.txt
> new file mode 100644
> index 0000000..982a30b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/devfreq/devfreq-cpufreq-map.txt
> @@ -0,0 +1,53 @@
> +Devfreq CPUfreq governor
> +
> +devfreq-cpufreq-map is a parent device that contains one or more child devices.
> +Each child device provides CPU frequency to device frequency mapping for a
> +specific device. Examples of devices that could use this are: DDR, cache and
> +CCI.
> +
> +Parent device name shall be "devfreq-cpufreq-map".
> +
> +Required child device properties:
> +- cpu-to-dev-map, or cpu-to-dev-map-<X>:
> +			A list of tuples where each tuple consists of a
> +			CPU frequency (KHz) and the corresponding device
> +			frequency. CPU frequencies not listed in the table
> +			will use the device frequency that corresponds to the
> +			next rounded up CPU frequency.
> +			Use "cpu-to-dev-map" if all CPUs in the system should
> +			share same mapping.
> +			Use cpu-to-dev-map-<cpuid> to describe different
> +			mappings for different CPUs. The property should be
> +			listed only for the first CPU if multiple CPUs are
> +			synchronous.
> +- target-dev:		Phandle to device that this mapping applies to.
> +
> +Example:
> +	devfreq-cpufreq-map {
> +		cpubw-cpufreq {
> +			target-dev = <&cpubw>;
> +			cpu-to-dev-map =
> +				<  300000  1144000 >,
> +				<  422400  2288000 >,
> +				<  652800  3051000 >,
> +				<  883200  5996000 >,
> +				< 1190400  8056000 >,
> +				< 1497600 10101000 >,
> +				< 1728000 12145000 >,
> +				< 2649600 16250000 >;

Now we have frequencies listed in multiple places, the OPP tables and 
here? Perhaps it is grouping OPPs that should be done.

This all looks bolted on and very much Linux specifc.

Rob